Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I am having nrf52833 module where I am attempting to run buttonless DFU for this I have made some changes in ble_app_uart_pca10100_s140.hex and have used
SoftDevice as...
Hi,
I got a brand new nRF52832 DK today and wanted to program it but the USB is not recognized at all therefore the nRF Programmer shows no programming option.
I connected...
Trying to integrate the serial part of the example code for use with a custom nRF52840 board. The problem is that I'm getting an error in uart_callback_set(uart, uart_cb,...
I use `west debug` to start `gdb` for debugging nRF5340DK
when I use `west build` to update the image, I use `load` command inside gdb CLI, the new `zephyr.elf` is loaded...
I don't know if this is a hardware or a software problem. My nRF52832 code runs correctly on a PCA10040 development board (UUID = E9:4A:AF:04:D2:16). My custom hardware advertises...
My software sent 2422, and I saw it on the net. 2417 also has one.
And the same goes for everything else, which is basically 5M off.
What is the reason?
Hi all,
I am working on troubleshooting intermittent application resets with an nRF52840 and nRF Connect 2.6.1. Codebase is small, complexity of the project is still small...
Hello,
I'm working on a BLE central multilink application, where I want to get the list of all peripherals in range, In order to let the user select the needed periherals...
I implemented UART communication as follows, but occasionally the same data is sent twice.
Enter the critical region (app_util_critical_region_enter).
Store the transmission...
hello!
I'm using 'NRFX_LOG_INFO' for debugging purposes. However, the code seems to stop progressing when 'the NRFX_LOG_INFO' statement is removed from the section below...
Hi,
I am using an nRF52 DK board to perform some very simple tests. All I need to do is receive a line of text over serial, perform some calculations and return another...
HI
I'm trying to use lpcom to detect when the battery voltage is dropping.
The configuration is as follows: 5V battery voltage output is reduced to 3.0V through LDO...
For my application I need the UART TX/RX pins pulled low until I am ready to turn on the UART. Is there a method in Zephyr to do this? Currently when Zephyr starts it reads...
I saw some similar question, but none is what I am experiencing.
I notice some weird behavior while testing DMA mode, so I made a simple setup:
I set the DMA buffer to...
