Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
HI,
we are working with
nRF5 SDK v15.2.0 ------------------------ Release Date: Week 37, 2018
Our use-case has a central device, which has 7 to 10 peripheral connected...
Hello,
We are using nRF Connect SDK 1.8.0 with nRF52832. As per the nRF Connect Documentation, when there is no active task, idle thread is called. Could you let us know...
Good morning,
I' mi trying to improve power saving on a device and it would be great to trigger:
1.an NRF52832 input pin transition triggers a "SPI1 instance" reading...
Hello,
I want to send 614.4 kHz clock signal to GPIO.
I checked that GPIOTE example could be used for this.
When I update uint32_t cc_value at nrf_drv_timer_extended_compare...
In searching, I haven't been able to find much information on implementing USB CDC ECM. Has anyone successfully implemented CDC-ECM with an nRF52? Alternatively, has anyone...
Dear nRF,
I know this topic has been covered many times, but I am unsure how I can change the uart pins for BLE 2-wire? I have not found any configuration for it inside...
Hi,
We've been in the process of debugging our development board but are having issues. When we try to connect to our board we get:
ERROR: [SeggerBackend] - JLinkARM...
I am using the Segger interface for designing an nRF52 based device. I am planning to use SWDIO SWCLK VTref and GND pins on my device. Is it necessary to connect the nRESET...
Hi!
We upgraded our node version 12.x to v 14.x and are trying to run in on Ubunto. "yarn install" trying to download pc-ble-js driver automaticly from the rebository git...
Hello,
I'm working on getting PSM mode with the Serial LTE Modem on the nRF9160 v1.0.0. The power consumption of the modem (26.4 uA) is too high compared to the documentation...
Hi.
I am using nCS with vscode to develop an application, So far I was only working with peripherals and my build file (.bin) size was about 70kb. Now I want to add BLE...
Hi,
I have a strange question about app_buttons, I have two buttons, only one of the buttons is initialized, which works well, but once both buttons are initialized at the...
Hello,
I am currently trying to include one of nordics flash examples into my project. Ive tried both, flash_fds and storage example. Unfortunately both will assert after...
Hello,
Is it possible to get an example for pc-ble-driver iBeacon detect/scan example.
I see only that one with heart rate, not sure what to modify for iBeacon scan/filtering...
hello everyone ,
i have posted a problem regarding Adding BSEC(bosch sensor ) library using vs code for thingy91 13 day before and i am still begging for help .If Edvin...
