Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
Hi, i am looking for basic start up parameters for a 24L01.
I do all my programm in assembler (sorry i am old).
what i aim to do is simple TX-RX, like a small remote...
I followed the steps below to set up my development environment, based on the instructions from link
Setup 1 1. Installed SEGGER J-Link v8.56a Path: C:\Program Files\SEGGER...
We have this custom sensor board, running nRF9160.
Application code built with SDK 2.5.0, running modem FW 1.3.2, and using LTE-M connecting to MS Azure IoTHub with MQTT...
Hello, I have an application, that uses the Bluetooth to do over the air updates using these two configs:
CONFIG_BOOTLOADER_MCUBOOT =y
CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU...
Hi all
I’m having a horrible time trying to get an nRF7002EB Wi-Fi coprocessor working with a nRF52840 via QSPI interface in nRF Connect SDK 3.0.2 (Zephyr 4.0.99). I'm using...
Hello,
We are working with Onomondo in integrating their software SIM. We have it working and sending and receiving data, but am having some issues figuring out what is...
Issue Summary: When running west flash to program my board using the UF2 runner, the process fails with an OSError related to copying the .uf2 file to the UF2 bootloader drive...
Hello!
I can use the offloaded sockets driver with these configuration options on the native_sim target:
CONFIG_NET_DRIVERS=y CONFIG_NET_NATIVE_OFFLOADED_SOCKETS=y
However...
Problem:
I am working on USB, CDC ACM, USB Mass Storage (using SD Card). I currently want to be able to still use the USB stack functions with only my USB Mass Storage being...
I'm experiencing an issue with my Power Profiler Kit II (PPK2) when using nRF Connect for Desktop .
System configuration:
nRF Connect for Desktop version: 5.2.0
...
I am using the 54l10 chip, and after compiling the project, I will receive a hex firmware and a zip update package. The bin firmware and hex firmware in this update package...
Hello Nordic team,
I would like to check if you provide a template for RED-DA EN18031 for nrf52840 which we can use to modify and fill based on what we have implemented...
I use nRF5340 audio DK,iso_time_sync example, can successfully send BIS data, then I use DK as controller, bumble( google.github.io/.../index.html) as host and it fails to...
Hi, I am currently integrating nRF52832 with TLV320AIC3104 codec. I have successfully initialized I2C and I2S communication between the two boards and configured nRF52832...
Hello,
I am evaluating the nRF54L15 for potential use in a new product. I did some measurements of the average current consumption and the vaues were a bit higher than i...
