Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hello,
I am porting the secure serial bootloader from the nRF52833 DK (PCA10100), in which it works fine, to my custom board. I press the button and turn my board on to...
Hello, all
Following this ticket ( Configuring ADC sampling rate and simultaneous reading from multiple channels. ), I found a great example code that sends readings from...
I'm using an nRF52840 Adafruit Feather Sense to communicate with a program on my computer over an OpenThread network. My computer is using an nRF52840 DK board as a network...
In other words, is it likely that the EasyDMA that's scheduled after the first HOST->EPOUT completes will copy bytes that have been overwritten by the second transfer?
I...
Hello,
My device based on ble uart app with nrf52832 operating with 2 AA batteries. It has 4 LEDs and 4 buttons. 4 LEDs are always on for indication but when a button is...
I'm blocked trying to get an Nrf52 application developed under v1.3.0 SDK work with FOTA.
My application is working fine. FYI, its on custom hardware derived from nrf52832_mdk...
Hello everyone,
I have a setup with two DK52 (nRF52832) with a mesh level client on one board and a level server on the other. Everything is working fine, no problems there...
Hello NCS team,
Target : Custom nRF5340 board NCS Version : 1.5
After observing sub-standard radio performance on my custom nRF5340 board, I realised that the XOSC32MCAPS...
Hi,
I'm trying to connect to aws iot but I need to set my MQTT_BROKER_HOSTNAME
In the documentation it says:
By default, the sample uses nRF Connect for Cloud’s MQTT...
How does one measure CPU load in a 52840 application where softdevice is used? I would imagine this is a pretty standard thing that people would want to do and I would be...
Hi,
I am having problems adding the MAX6675 device.
I using this code
and this prj.conf file.
and this overlay file
and try to build using the command line...
The JLINK driver is not working on my laptop although I see it; not sure why. When I plug in the USB a board LED flashes and I can change LEDs 1/2/3/4 with pushbuttons 1/2...
I've been getting Timeouts during provisioning with "Requesting Composition Data" when provisioning via iPhone using the nRF Mesh app and nrf52840.
I've had problems getting...
Hi Nordic,
I am trying to make the OTA part for the nrf52840 to be possible. My nrf52840 is connecting to the server through the 4G module, I am trying to receiving all...
I modified the ble_app_uart example to run on the PCA10059 by altering the flash_start, size, ram_start and size linker settings. I also selected two GPIO for the uart pins...
