Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I am writing a code to blink the LEDS , the 3rd one is not turning off.
Here is the code-
#include <stdbool.h> #include <stdint.h> #include "nrf_delay.h" #include "boards...
Hi,
My device is using nRF52840 with s140 of SDK v16. BLE feature is used with SD .
Sometimes application hard faults in SD are observed in devices deployed. It is quite...
Hello,
I find that after I DFU a new application (using the nRF Connect Mobile App), my device boots into that new application and reconnects to the App, as expected. Then...
Hi,
I am using nRF51822-CEAA with S110 SoftDevice on a custom board which is commercially deployed now. I am using IAR 7.80.2 and Segger JLink Ultra+. I found there are...
Hi community ! I saw a lot of topic about that but i'm working with SDK_Mesh_v4 and i don't get what i want. Does someone have a working example of sending string over Mesh...
Hello!
I have a rather vague question and want to apologize for that beforehand.
I was wondering if it is possible to connect a JPEG camera to the nRF9160 DK (i.e https...
Hi, We are in the production phase of our development, and inadvertently , the mcuboot bootloader set the DCDC on a few units. As described here, https://devzone.nordicsemi...
Problem with setting two uart on pca10040 board
hello
I am reading the log by teraterm by connecting pca10040 board to PC via USB.
I am trying to connect 6pin and...
We are using manufacturer specific data to broadcast data at 10Hz.
We're about to do some testing to evaluate different adverting and scanning parameters to find the best...
Many of the sdk_config.h examples have both NRFX_FOO_ENABLED and FOO_ENABLED defined.
So, imagine my surprise when I change, say, NRFX_TIMER3_ENABLED to 1, still get link...
Hi, is it possible to measure NRF52832 vdd voltage using LPcomp. I know I can do it with ADC but it draws a lot of current. I'm thinking if I can compare VDD to lpcomp reference...
Overview: number of bytes sent by ble_app_blinky at notification is determined by (note my changes for debug:
in ble_lbs_init() of ble_lbs.c and not by:
in ble_lbs_on_button_change...
I aam badly stuck in this error and dont know what to do with this i have downloaded ble adc scan mode example and running it on sdk17 using SES .i have removed powerclock...
Hello,
I have Thingy:91 connected to the cloud. I see that data is send correctly in json format (on nRF Cloud terminal). Is it possible to plot graph or download csv file...
The modem on the nrf9160DK (modem fw v1.1.0) appears to get stuck in searching mode. It doesn't happen all the time, and I was able to create it with the following AT commands...
