Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
I have been running a mqttsn client publisher/subscriber project (based on the example) successfully for some months. I have added a mosquitto broker to the raspberry pi border...
We are designing BLE products based on the Nordic nRF52840 chipset and star network topology which are used indoors, according to the network structure, we use one Master...
Hi everyone!
I've been using the Power Profiler Kit quite successfully for the past few months. Instead of using the UI, I designed a python app to communicate with it ...
The nRF52840 OPS 0.5.1, describes nWRITE,BLOCK as the amount of writes allowed in a block between erases, and lists nWRITE,BLOCK = 403 Maximum.
It looks like 8 blocks are...
Hi folks,
I have a system basically working with the following setup:
#define MIN_CONN_INTERVAL MSEC_TO_UNITS(7.5, UNIT_1_25_MS) #define MAX_CONN_INTERVAL MSEC_TO_UNITS...
adv interval : 1s
adv data: 31byte
tx power: 0dBm
MCU: nRF52832
The power consumption is shown in the figure below,when I don't enable DCDC.
what may be the reason...
I followed all the steps mentioned in the tutorials. In one of the threads, it was mentioned to erase all and then try and it worked for some. I tried that as well. Still...
I'm using nRF Connect v2.6.2 on windows 10 using an nRF51 dongle to update my target OTA. Target is an nRF52832, softdevice s132 v6,1,1. The DFU process takes like forever...
Hello,
I work in a startup, and we aim to measure cooling conditions in data centers.
For that, we have developed customs boards with a nRF52840, and we are using Bluetooth...
Hi, I am currently using Nordic nRF52 dev board (with nRF52832 SoC) and trying to test "dfu/secure_bootloader" example in that board. Because my target ship is nRF52810 I...
Hi,
We would like to activate the "legacy" 4G DRX with a period of 1.28s. Do you confirm that the needed AT command is: AT+CEDRXS=1,4,"0000" ?
If not, could you provide...
Hi
ENV: nrf52 + SES + SDK15
I have a scenario where the nrf52 peripheral can be advertising at the maximum interval allowed (~10s) . During the advertising it is also...
We have a Nordic Thingy 52 sensor and a Raspberry Pi which are connected through Bluetooth. The Raspberry Pi is also connected to the Internet via WiFi.
Initially, we tested...
Hi,
This is unrelated to my other open question.
I have programmed the secure ble bootloader and can OTA flash the buttonless bootloader example .
My problem is that...
We have several nRF9160DKs which have previously been registered in nrfcloud, but we have lost track of the owners. The kits are useless until we can deregister them from...
