Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi to all,
i am developing a device with nrf52840 soc and i want connect to Windows 10 though ble connection. in my device i had implemented an HID service that should act...
Hey is it possible to use advertising beacons together with an server or there will be some collisions in message reception ?
what i want to do is: setup a mesh which consist...
Is there some guide to help implement UART using nRF Toolbox source code for ios?
I am trying to figure out how to use:
Scan, connect, pair and UART
Any help apprec...
when performing db discovering using a peripheral nrf52832 (running sample dfu project) from sdk 13 from a nrf32832 central on sdk 14 I notice that the db discovery event...
Hi Sir
I would want to download code to Ublox NINA-B301 by command line, but it looks not working, please help.
nrfjprog.exe -i 483064601
nrfjprog.exe --family NRF52...
Hi,
I'm trying to perform a DFU firmware update via command line using nrfutil dfu ble.
The same update using nRF connect works fine. The dongle is flashed with connectivity_1...
I would like to have a ZigBee stack running on the 52840 and use door/window (contact) sensors as well as motion (PIR) that are available on the market today to connect to...
Dear Sirs!
I use compiler IAR 7.80 with Nordic SDK 12.2
Softdevice
s132_nrf52_3.0.0_softdevice.hex
I have very strange issue in debugger.
Break point works, but...
Hi folks,
I try change blinky code for nRF52810 SoC. I must create own timer. I dont know app_timer example help for me?! I want to do when power on leds on 2 seconds...
Hi All,
I am developing an application in which i am interfacing the nRF52832 with an ADC via SPI.
I am doing channel multiplexing (2 channels) such that when i get data...
I'm aware of the limitations on using "printf" in a non-debug environment, but apparently there must be something similar with sprintf. I'm using it to load a value into a...
Hello,
There's a problem compiling the standard ble_app_uart_pca10040_s132 in Segger Embedded Studio for ARM V3.40. The UART example is straight out of nRF5_SDK_14.2.0_17b948a...
Based on the demonstration video of Thingy , I can have a view on Thingy is changing its color when it is given different command using the apps.
1. As if I want to send...
Hello, I want to include Mesh Serial Example into the Mesh Light Switch example.
The aim is to allow the serial device to listen to the mesh messages.
What is the best...
