nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
Hi,I have trouble when I try my nRF51822 board with example program of hrs. I use nRF Master Control in my phone to connect with my board.scanning is ok.But when it try to...
Hi guys,
I'm investigating on a problem we found in our system. It seems not related to our custom pcb or firmware, you can replicate it with the following setup.
Setup...
I will need to store some data (and edit it again later) and fetch it later in the nrf51dk even after turning it off and back on.
How can I store such persistent data in...
Some situations like heavy ble activity causes the nrf52832 to restart without hitting breakpoints in the NVIC_SystemReset.
Assuming there aren't any hardware issues, is...
Can I use J-Link EDU for nRF52840-PDK , nRF Connect , please?
Is it sufficient?
What the J-Link PRO provides for nRF52840-PDK, nRF Connect that the J-Link EDU does not?
Question preamble
I am writing a bluetooth application where two nRF5 devices will be in a master / slave configuration. However, I want to be able to flick a physical...
Hi.
I have an application that needs a low security encryption. Therefore I want to use "Just works" encryption. The pairing process is assumed to be in a "safe" place...
I am having a strange problem. After I flash the program to the NRF52 and do a reset (does not matter whether it is a soft reset or pin reset) the system (DK and my own board...
Hi,
i read this post:
devzone.nordicsemi.com/.../
and found the PCA20006 project but i cannot load it to the beacon. I can find proper instructions on how to load...
I had initially added ble_dfu buttonless DFU support (unbonded) to my app per instructions here: infocenter.nordicsemi.com/.../service_dfu.html
Long story short, based...
What unique information can I use to know which physical device disconnected for example? Say I have a MAC address or a name encoded into the advertising packet. Correct me...
Here the connect method is called
err_code =
sd_ble_gap_connect(
peer_addr,
&m_scan_params,
&m_connection_param,
APP_BLE_CONN_CFG_TAG);
In the ble event...
I'm tring to connect my phone to the multi-connect example client app
I'm tracing the ble events in the ble_evt_handler.
When I open the server app on my phone, I see...
Hi Engineers!
faced with a problem of SAADC impedance too small (4,7K)!
We use SINGLE ENDING 8bit mode with following settings:
NRF_SAADC_REFERENCE_VDD4
NRF_SAADC_GAIN1_4...
