Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
I'm using the nRF5340 DK with the HRM example. My phone is HUAWEI mate 10 (Android 10).
I could scan the Zephyr Heartrate Sensor in nRF Connect App and nRF Toolbox App ...
Hi Team,
In continuation with Case ID: 269054, 269278
I am using NCS (as suggested) to avoid high current consumption happening during softdevice initialization.
I set...
Hi, I'm enthusiast of nrf5340 DK. BUT: in the samples I'm not able to find some viable openamp (other ipc seems to have the same problem) example. I am looking for a way to...
To the kind Nordic support team,
I have got a nRF52833 based Raytac module I'm using to develop before using a custom board.
I'm using Microsoft Bluetooth Virtual Sniffer...
Dear Hardware Application Engineer,
We are using nRF ASICs for our IoT products for the past two years.
In nRF52x series products, forex. nRF52840, there is a power supply...
When I do a DFU on my device (nrf52832 with Zephyr) using nrfConnect, the update is successful, but I get a message in the log stating "Length of data to send exceeds MTU...
Hi Nordic,
I am using the Raytac module with the nrf52840 inside, I have set my hardware as mode of Reg0 DC/DC enabled. Which disconnected the VDD and VDDH. Also I have...
Hello,
We need to use the RX TX on TTL level. That is possible with the nRF24L02 chip, as fa as I can understand from the datasheet. But we also need to use 8 bits, even...
Hello,
I am using nrf52840(nRF5 SDK v15.2.0). armgcc compiler, softdevice s140 hex, and application + OTA bootloader combined hex file.
in my application, I have some...
Hi,
We're developing with Zephyr OS on nrf9160 and recently added SD Card support. We build our application also for qemu_x86 for testing purposes and would like to add...
Hi!
Hope you are doing well!
I was wondering if we can use a normal characteristic to do the buttonless DFU (i.e. transmit all .hex file through that normal characteristic...
Hi, I have a few questions related to extended advertising. I am trying to receive extended advertisement sent from an nRF52832 with an ios device. The Softdevice used is...
Hello!
I have the Serial LTE code running on an NRF9160 DK and sending AT commands to publish data to MQTT broker.
It happens sometimes that the NRF9160 looses network...
I want to verify below configuration can operate or not in bluetooth ?
Fitness tracker is preset in connected mode. Broadcast mode can be selected as fitness tacker have...
