After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Based on the nRFUart demo, I added a masterEmulator.DiscoverServices() block before the DiscoverPipes() block in a very similar manner. Purposed is to be able to get more...
Hi,
I am able to sniff and decrypt all the packets in Mesh Network as per NRF_Sniff Procedure Manual.
But unable to decrypt the packets received between the Low Power...
I'm developing an application where there will be multiple central links to relatively low bandwidth sensors and 1 central link where sensor data will be streamed. The throughput...
Hi teams,
I am developing with Mesh SDK 4.0.0, and suffers from random fault during long-term test.
The last readable callstack position is the below.
The callstack...
I am currently trying to use a nordic semi ppk and nrf52840 to read current in the nordic semi power profiler software. I am able to flash the DK successfully (while P22 is...
I have a 9160 DK board with lte_ble_gateway on the 9160 side and hci_lpuart on the 52840 side. It works as far as being able to send and receive BLE messages but it has faults...
Hello,
Previous revisions of the nRF SoC's such as nRF52840 and nRF52832 have had specifications for certain IO to be low frequency < 10Khz and standard drive only because...
Hello
I'm facing an issue with app_timer_start. Indeed, with small values, sometimes, the app_timer_start won't start the timer. As a result, the interrupt handler is not...
Online Manlio 6 minutes ago
Hi,
I add NFC to my project with freertos. The initialization of nfc is ok. After running few seconds ,it hang. If I comment the usr_nfc_init...
Hello,
I work with the ATE using Algocraft WN series programmer.
It has directly access to GPIO registers through SWD interface with WRITE / READ / COMPARE commands. ...
Hi,
I was tracking down a bug that resulted in a secure fault exception. To save some time tracking it down I enabled logging in the spm. However this resulted in an escalated...
Hello,
So I am just real confused on how the softdevice programming works via the open_bootloader right now and can't seem to track down the documentation I need to be successful...
I'm running a code based on the ble_app_uart example using the PCA10059 dongle. I have the dongle connecting to a raspberry pi 0 W via BLE and when this runs using a power...
Hello,
at the moment I am working on a project with a nRF52840DK as central and multiple nRF52DKs as peripherals. The code on the central is based on the "ble_app_uart_c...
