I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Hi all,
I am extending the BLE Multi-link example from SDK 15.2.0 in order to have some characteristics as BLE Mesh. I would like to use UUID filter to scan all peripherals...
I'm seeing similar problems to others in getting highly unreliable connections to the network. I *VERY* occasionally get LED3 and LED4 to blink simultaneously, but it's very...
Hello.
I take the flash_fds example from nRF5_SDK_15.2.0_9412b96, but I am not going to use the CLI (command line interface) because I take the FLASH written, reading capability...
Hi,
I am using nRF52832's ADC function to do my project, and I have an analog signal level problem.
I am try to connect MPX5100 sensor to nRF52832's ADC port, but the...
I am trying to use ARM GCC in macOSX and successfully generated .HEX file with the most simple project: the blinky project without softdevice. After setting up the project...
I am trying to use dsm_local_unicast_addresses_get() to store the address of each node, however it seems that when the board is restarted the value is lost, and node_address...
Hi,
I have troubles using nRF Mesh with my Vendor model.
I have made a Vendor Model that should allow me to send messages through Mesh. Once my boards are provisionned...
Hey everyone
This is sumanth, I am working low power node in mesh networking, I followed the procedure mentioned in below link for building and flashing
https://www.nordicsemi...
Hi I have a device which can get RSSI value from other devices.
But how do we get RSSI of my device itself.
i.e How to print RSSI of local device on the same device terminal...
Hello everyone,
Today I worked on custom bootloader and according to the article infocenter.nordicsemi.com/index.jsp I tried to load output hex file from IAR on board via...
I want to add a new ble service in hrs example(sdk15.3),I build and run the hrs example.and then I open the terminal emulator, but I can't find anything.I try to click the...
I want to use nRF52840 BLE with STM32F745ZG microcontroller and using atollic studio for coding. is it possible to use nRF52840 with the microcontroller? if it is possible...
I'm using SDK 15.1, nRF52 in custom units, toolchain GDB, addr2line
A little background -
We use System off mode and then use a button press to come out of it.
Before...
