I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Hello,
I'm using low power comparator with cross detection.
It works but I can't detect if it's failling or rising edge.
Can we detect simultaneously DOWN and UP...
Hi,Everyone! Now i have the board nrf52832 and i'm trying to get the battery value and send by using saadc.
i have read the example of ble_app_proximity and saadc,and i configure...
Hello! I compiled hex file with NRF52_BOOT in mbed cli. It was programmed successfully. Mbed os version include fix to use nrf52 DFUService. Bootloader is loading correctly...
Hi Nordic guys,
we are observing a strange behavior. Here some background on the project:
we are developing a peripheral device that asks via L2CAP signalling connection...
Hi,
I would like to know, whether it is possible to use a TCXO with single output as a LFCLK source, i.e. connecting the TCXO output only to XL1, instead of connecting an...
Hello everyone, I encounter a question. I follow below link to solve the issue.
https://devzone.nordicsemi.com/question/104118/adding-pwm-to-ble_template/
I've set the...
We are currently porting our proprietary stack from the nRF51 to the nRF52.
To save on BOM we are using an external 20ppm 32Mhz crystal to synthesize a 32Khz clock (power...
Hello,
I have develop an android application which connects to BLE device and perform read and write operation, so for this i was using Android-nRF-UART .
But my application...
In the release notes for the IOT SDK (which as the MQTT examples) it says: "Once BLE link is disconnected, lwIP example applications no longer get a global prefix. The only...
Hello all,
I am new to ARM architecture with some prior experience in Arduino based application development and some FPGA experience. I have a few queries:
Should...
I'm developing a project based on the Nordik UART Service and I wouldn't use pairing as in the example.
However I have some problem when a central device is already connected...
We're targetting the nRF51822 and use the pc-ble-driver (via connectivity_1.1.0_115k2_with_s130_2.0.1 )
Currently I'm using the dev board and the virtual COM port connection...
Hello,
I am trying to move from ARM Compiler v5.06 to v6.4, but I encounter an error, which I cannot handle.
The project builds fine with v5.06. When changing to v6...
