Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
8.0, multilink example, peripheral, s110 softdevice.
By walking through sections of codes and doing some research, I reckon if a connection were being established after...
I try to Development with GCC and Eclipse following tutorial
but i get some problem , which i can not solve alone.
so hopelly someone can help me to solve it ,thx!
that...
Hi，I use nRFgo Studio to erase nRF51822, like this
but it display: ERROR: Invalid serial number!
I found the question how to use nrfjprog --snr??? ，I can get the...
I am using the nrf24l01 on a FRDM k64f board, I want to communicate between the board and my laptop, so I have bought a nrf51 dongle.
I am using mbed on the k64f board...
I try to create a custom boot loader that enable to update soft device via data come in from SPI msg. When I try to use the command nrf_nvmc_page_erase() to erase the flash...
Hi everyone,
I'm a beginner in Android development and BLE environment, and I want to communicate with the nRF52 card using an Android app. In fact I have to develop an...
hi,
I am using the nRF51 with code from SDK 9, as well as the S110 softdevice and made a custom service(128-UUID) with bond using device manager.
connection and service...
Hi,everyone,
I would like to know that what's the dedicated bonding ?
I saw this in the introduction of a BT chip.
I am confused with 'dedicated bonding'.
And what's...
Hi,
I am using the nRF52 with code from SDK 9.2, as well as the S132 softdevice. I basically ported code from the ble_uart_app into the twi_example to send data over bluetooth...
In the very first blinky example from the nRF52_SDK_0.9.1:
#include "stdint.h"
#include "stdint.h"
#include "nrf_delay.h"
#include "nrf_gpio.h"
#include "boards...
hello,my experiment phenomenon is:one nRF24L01's channel is 0x0A,used as send terminal；the other one nRF24L01's channel is 0x02，used as receive terminal；receive terminal can...
I try to make a build of the example ble_app_hrs_rscs_replay_pca10028 (central and peripheral experimental) in SDK 10. My MCU is nRF51822-CFAC, and I'm using IAR compiler...
I'm using custom board with 32MHz oscillator and S110 SD 7.1 (SDK 6.1).
Somteimes (quite rare) the chip completely hangs when calling sd_flash_erase in pstorage.c.
Only...
