I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
After installing the USB driver for the nRF52840 dongle and using it successfully, and then connecting the nRF52832 DK it fails with "error occurred when opening port. Errcode...
Hi everyone,
I was trying to use QSPI interface with the on board external flash memory MX25R6435F on nrf52840 PDK
This is what i have observed, Inside the linker tab...
Hi, I have nRF51822 Board
Can I make it as a beacon kit?
what changes do I need to do to change that as a Beacon? any Source and Instructions are very helpful for me....
We need our PCB assembler to be able to program nrf51822 modules in situ. We have tracked the PCB to include a tag-connect footprint to this end. The assembly house will purchase...
Dear all,
I have an issue using USB bootloader for NRF24LU1+ device.
I've used a USB dongle and programmed USB bootloader to chip via SPI using external programmer.
...
Hello guys,
I have tried to get Nordic-Thingy52-mesh-demo working, but now I don't see it works according to description done.
I have followed all steps provided on...
Hi,
we are developing against the nRF52840 chip. We are interpreting the documentation as indicating that each pin can do all of GPIO, PWM, I2C and SPI. Are we reading this...
Hello,
I'm using SDK 15 and I just started to run the "ble_app_uart" example code. I'm hoping someone can help me find where the data sent from the nRF UART mobile app is...
I am using few keys that are 20 byte arrays, these are unique for each chip. Right now they are hardcoded. I don't want to recompile for each device. I want to write to these...
Hello,
What is the best way to do migration between SDK 11 to SDK 15.
There are guides for each step. Is the best way to do SDK11-SDK12 then SDK12-SDK13... ?
Thank...
Hi,
I just switched over from the nrf52840PDK to the nrf52840DK and I'm running into an issue where the DK board is not firing the NRF_USBD->EVENTCAUSE = Ready event....
Hi,
I'd like to inquire about the recommended configuration for RF conducted emissions testing for the BTLE radio on the nRF52832. As in the reference circuit provided...
I am trying to send more than 255 Bytes of data over I2C so I break it up into 255 byte transfers within a transaction.
I notice a stop/start condition is sent between I2C...
Hi,
I am trying to have two instances of SPI with the same data and clock pins but to two different devices and thus two different select pins.
I have set all the SPI_Enable...
