I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Hi,
The nRF Connect iOS and Android apps provides detailed instructions and functionality for enabling the device boot loader via the iOS/Android] mobile apps. When running...
Hi,
I have a application where the TWI is always reading a sensor in the main task.
When the DFU requiere to reset, frequently the TWI is busy and the current frame is...
I am using nRF5_SDK_15.0.0_a53641a with a nRF52 Development kit. The board is Rev 1.2.4 (the sticker on the bag says nRF6827 and the sticker on the chip says PCA10040). I...
I am struggling to configure all of the options I desire to on the the "ATT-MTU Throughput Example". This is the version provided in the v15.0 of the SDK, with the hex file...
Hi,
I have two nrf52dk devices.
I Want to test the BLE examples which can exchange Bytes of information between each other and display over the UART.
Which examples...
Hi.
My target board has a power switch that is managed by GPIO.
First-time, a user clicks the button, the GPIO is turned on and the system wakes up.
In reset case(Firmware...
I'm troubleshooting my NFCT state machine -- I'm getting a lot of FRAMEDELAYTIMEOUT errors and can't understand why, I'm triggering a TXSTART ASAP... but that's another issue...
Hi there,
Is it possible to feed XC1 or XC2 with an oscillator output rather than using a crystal?
It would make sense for me in terms of application but I cannot see...
hello , I followed this tutorial : devzone.nordicsemi.com/.../wireless-timer-synchronization-among-nrf5-devices
when i put the button 1 i have just a signal of 2 second...
Hello,
I want to use the D-/D+ as general I/O pins but noticed that it's not mentionned "General purpose I/O" in these pins.
Are these pins only available for USB ?...
Hi,
I am working with the examples/peripherals/application template code from SDK 15 against the brf52840-DK board. I am running Linux as my dev environment I am using the...
Hi there,
I was wondering if there was an easy way to output the LFCLK from our 32k crystal on one of the GPIO pins of the NRF52840?
Couldnt find anything in the Spec...
hello , i have 1 nordic card (central) and 4 nordic card (peripheral).
At this moment the 4 peripherals send their data to the central without problem one after the other...
Hi
I have RGB LED Strip of 5 numbers and giving out 5V from external power supply
This LED Strip has WS2811 as LED Driver ( https://cdn-shop.adafruit.com/datasheets/WS2811...
Dear all,
It's strange that this seems to not have been asked before... since the nRF52840 can be powered directly from a LiPo battery, I wonder if there is an UVLO protection...
