Hello,
I have downloaded the software related with the "nRF51822 Bluetooth Smart Beacon Kit" in order to modify typical iBeacon's parametres such as UUID, Major ID, Minor...
Hello,
i would like to know if the new SoftDevice 130 for the nrf51822 is compatible with the DFU OTA bootloader example provided in the SDK (nrf51822/Board/nrf6310/device_firmware_updates...
Can I get uuid of central device from peripheral device(nrf51822) ?
I want to check out which smart device is connected.
May be I can tell central is iphone4s or iphone5...
Recently s110_nrf51822_7.0.0 softdevice has been released. I cannot find specification where those new amazing features (they are impressive, indeed :) ) are described, so...
Hi All,
Please correct the following in my understanding. Also , i am planning to build a
remote controlled device using a PWM output. How does ATT,GATT and GAP affect/influence...
Hi,
I am running a modified version of the light switch example, where I have modified the generic on off model to send byte arrays.
So I have been changing my models...
Environment:
nRF5 SDK version: 17
SoftDevice: S140
Tool: Segger Embedded Studio
Debugger: J-Link EDU Mini
Board: Arduino Nano 33 BLE (Using SWD pins with the J-Link...
SDK 15.2, nrf52840 SD 6.1
I'm having an issue where a reset with RESETREAS DOG 0x02 is not coming through the WDT handler before executing reset. I can force this reset...
Hi,
I have the following application in mind: I want to create a bluetooth mesh network, in which one node will broadcast sensor readings, some nodes will be used to hop...
running sdk version 16 on nrf52833 ,
1. on power on , start advertise - " nrf connect" connected successfully ,
2. disconnect from the "nrf connect" , start advertise...
Hi folks,
I'm trying to find a pcb prototype manufacturer which supports the via-in-pad requirements for the nRF52840 package (i.e. 0.15mm hole size with 0.1mm annular ring...
I'm using the nRF52832, and taking ADC measurements, with 14 bit resolution and with Oversampling disabled. The nRF52832 Product Specification mentions the saadc can be configured...
Hi,
I modified the ble_app_att_mtu_throughput example to scan and advertise simultaneously. I want to have two nRF52’s that can read each other’s advertisements and pull...
Hello,
I have a system composed of one central that needs to 1) briefly connect to many (100+) peripherals, 2) download a small amount of data from each, and then 3) disconnect...
Hello,
I am working with SDK 15.3.0 and the nRF 52832. I am working with the Segger IDE v4.16.
I attempted to load the scripting as instructed in the SDK documentation...
Hi, I had this working, I'm sure of it. Now though I get 100% duty on one channel and 0% on another. Something's not right. Pins are correct, my focus is CFG_PWM_OUTPUT_FRONT_NUM...
Best regards:
Once the data was received in PRX, Is there a way forward (or modify) to PTX the same data and deliver it together with ACK payload in the same transaction...
Hello, i would like to test usb_msc example on a custom board, and i have few questions:
- will this QSPI flash chip work with nRF52840 QSPI interface, and is it sufficient...
Hello,
I'm doing some clean up in my code and i wanted to use only nrfx library as it advised to do. Regarding the watchdog i have set in my app_config.g file (used by my...
Hi,
Right now i am working on mesh sdk 3.0.0 on segger embedded studio and board i am using nrf52832. In my application i am trying to implement the watchdog timer but it...
