Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi Community,
I am using ble_hrs_heart_rate_measurement_send API to send notifications to my central device which is a android mobile.
Recently I have observed packet...
Hi,
How are you?
Could help someone with a ask?
I am designing a plate and I am using like guia the nRF9160 DK. The Layer Stack Manager has configured the Top Layer...
path:
\experimental\cli\cli_agent_router\pca10059\mbr
When I execute "bdb start" in the serial port and then execute "bdb Legacy Enable", the terminal devices that are...
Hi Nordic Team,
My dev enviroment is as follow:
nRF52832(ble central)+ S132+ SES+ SDK 17.0
We are facing an issue regarding local BLE Address . When we are flashing...
Hello.
I am developing a peripheral roll using nrf52832 (S132 v7.0.1, SDK v17.0.0).
I want to know the information of the device that sent the connection request. Also...
Dear Nordic Team Support,
I am testing throughput on different environments, my goal is to stream data from custom-board to Laptop. I have set up some experiments as shown...
Hi all:
I am using nrf52840 hardware. nrf connect sdk.
I am using file system and mcuboot at the same time. When i call ` flash_area_open (id, & pfa);`, i got a wrong...
Hello,
we developed a proprietary protocol on top of IEEE 802.15.4 user zephyr on a nRF52833. Everything was fine with hal_nordic on commit 74b3b21f60aa3dc9a4364ffc28dbb47ad8b699a9...
When I pair the peripheral with a dongle connected to nRF Connect Desktop application, then disconnect and Connect again, the nRF Connect does not remember that it was paired...
I built the SMS sample without changing anything. I am using a Lebara prepaid sim card. I was able to exchange SMS messages from one cellular phone to another. I checked with...
Hello,
For a long range test between the nRF Toolbox Android app and the ble_app_hrs (in nRF5_SDK_17.1.0 package) over the nRF52840-DK. I would need to setup this board...
Hi,
I initiated pin 28 as SCK of SPI as normal condition, and I'd like to switch pin 28 as GPIOTE while receiving a command via BLE.
Basically this is how I achieve...
Hi,
I have loaded a simple application on my nRF52840 that just activates a GPIO as soon as it reaches the main loop.
The SoC is powered externally according to the chapter...
Hi,
We will create a ble peripheral device and also can handle timing-critical uart request. The uart will be always communicating and response time can't be slower than...
