Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi,
I'm using the example project usbd_msc and I am having no luck having the volume come up on windows when I plug in the nRF_USB line. I can see "nRF52 USB MSC Demo...
We are currently getting our firmware ready to test devices for FCC and other radio testing. We have an AThost-like setup that passes AT commands from a terminal over a BLE...
.Hi Nordic Support team,
I'm using NRF52832, SoftDevice S132, SDK version is nRF5_SDK_17.1.0_ddde560.
I want to transmit 9 bytes of data collected from an I2C sensor...
Hi,
the I2C burst write function below work perfectly <16 number of bytes. Once I transfer more that this, the return code throws an error "-28" and my scope doesnt even...
Hello, I would like to develop an automated tool for our production line to use to perform DFU on our nRF52832 system. Is it possible to communicate with the nRF52 Dev kit...
Hi, I developed a custom board and I am able to toggle other IO pins but somehow pin 10, 9 wasn't working. After some research, I found that NFC must be disabled to make it...
Hi,
I am trying to set EDRx en LOG_INF the result using following code:
static struct lte_lc_edrx_cfg drx_cfg ;
//enable EDRx
LOG_INF("== Setting EDRx =...
Hi,
I have a custom board with a nRF52840 and the nRF21540 FEM. To control my FEM, I have added the following to my code to my nRF52840_nRF52840.dts file:
/ {
nrf_radio_fem...
Hello Everyone. I tried to run the ble_app_multirole_lesc example on SDK 16.0.0 to test the numeric comparison match feature on bonding. And found that the handling of this...
Hello,
I am currently updating from SDK v2.3.0 to v2.5.2 but I am not able to get the 'psa' functions working correctly (as they did with previous SDKs).
I am trying to...
Hi, How to find out what function is being called, when sw interrupt occurs? I have created a timer that should call a function. But I'm having a hard time finding what function...
Hi,
I am working on custom board which has nrf9160 as modem and stm32 as host controller.
here I am used lwip stack on stm32 controller to get the IP address.
I have...
I'm trying to integrate AES-128 (ECB mode) decryption into my project
I've based it on the AES_CBC sample, and adapted it to use ECB mode instead of CBC. When I compile...
Trying to use the nRF Connect quick start with the evaluation board and the programming fails. 2024-05-22T09:09:27.145Z INFO Initialising nrfutil module: device 2024-05-22T09...
Hi,
I encountered an issue from my custom board who are using a nrf52832.
When i place my board in very cold temperature environment (around -35°C), sometimes the voltage...
