Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
We have unit testing working with the Zephyr Unity/CMock setup, however the test runner (test_runner_generate) ignores preprocessor directives (#ifdef) and removes them when...
I have an application that must manage different ble connection with different device (and so different UUID services). For the scanning and connection I used the bt_scan_filter_add...
I am using a ble+wifi module which is MS12SF1 which has nrf5340+nrf7002. It is connected with a pcb in which there are 2 inmp621 pdm microphones. I have tried integrating...
I have a dongle attached to my Windows PC and it has the nRF Sniffer firmware flashed onto it. I have also installed the nRF Sniffer extension for Wireshark.
When I start...
Hi
I have been able to work with the 'Lighting' demo BLE mesh application using the nRF Connect SDK with Visual Studio Code. I have even been able to add my custom board...
Dear Madam / Sir,
we started developing a new electronic device which uses Bluetooth 5.0 four years ago and are now ready to certify it. However, during testing we had to...
Hi,
I have designed a custom board, but after production, we are receiving very poor RSSI. I am looking to add an external antenna to the board to see if it can improve...
Hi everyone,
I'm designing a PCB using the nRF5340 MCU and the same matching circuitry (series inductor and parallel capacitor) with parallel ESD protection as provided...
nRF52840 NCS 2.4.1
I am logging to the FS backend. All the files have a date of 12/31/21 11:00.
How do you give the file system access to UTC time?
I have a UTC time...
I'm working on a project with the AD5940, and it looks like this case did the job.
However, I am using NCS v2.2.0 and not nRF5 v17.1 - so code translation is required...
Hi,
we are using nrf52840 and nrf SDK-16.0. we have achieved simultaneous connection and data transmission for 4 devices in Ble 4 (i.e. 1 Mbps PHY).
Now we are trying...
Hello Everyone! I am working on a zephyr project based on nrf52832_mdk hardware. I have a code that transmits data over BLE. The BLE connection name is, let say zephyr-connect...
Is there a way to modify the PHY layer, or SoftDevice, so that a timestamp is immediately read from a timer and forced into the manufacturer data right before transmission...
I have an application I am working on, and I created a custom structure rx_servo_t. The structure is meant to provide methods for controlling some off board motors via GPIO...
