Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hello,
While I was testing the codes, I just got a few errors and I am confused as to why it's happening. The questions are:
1) Sometimes, I get pm_conn_secure error code...
Hi Nordic Team,
In my project the function sd_softdevice_enable does not return in one specific case:
I call nrf_sdh_enable_request() before init of the ble stack. When...
I'm having an issue getting the SLM example to compile with UART2.
Steps to reproduce:
Configure project with UART2
See error pop-up
Compile anyways
See Undefined...
Hello, I am a beginner to start developing with your nRF52810 chip.
In the near future, I would like to implement Bluetooth long range communication with this chip.
...
Hello,
We are planning on running the nRF9160 with two supplies. VDD_GPIO=1.8V and VDD=3.8V to get the best cell performance.
Can you tell me if I can turn off VDD_GPIO...
Hi,
I develop a device with a GPRS modem. GPRS modem is controlled by nrf52840 and it is impossible to use two devices for DFU process.
SDK: 17.0.2
SoftDevice: s140...
I want to send adc data to Bluetooth.
I downloaded the source code below and compiled it. https://github.com/NordicPlayground/nRF52-ADC-examples/tree/master/ble_app_uart__saadc_timer_driven__scan_mode...
Is there sample code to use a FAT Filesystem on the Macronix memory on the nRF9160-DK? The full_modem_update sample uses the Flash but not as a filesystem.
It would be great...
I have a modified asset_tracker that has been running on all of the previous versions of asset_tracker. I have I2C settings in prj.conf as shown below that I copied from each...
I am just starting out with the nRF5340 and I see that it has an NFC antenna. Can it read an external NFC tag without additional circuitry or does it require an external reader...
Using SDK 15.2, PCA10056 Dev Kit. Segger Embedded Studio. s140_nrf52_6.1.0_softdevice.hex
Our Code (non Long Range) works perfectly! We are using it in a test for a customer...
I am using sd140 on a ble central and peripheral that uses the ble uart example code.
The peripheral always returns NRF_ERROR_BUSY when calling ble_nus_data_send(). This...
Is it possible to run ble_central and ble_peripheral as two threads using freeRTOS on the nrf52832 chip? Is freeRTOS on nrf52 is on an experimental stage?
Recently, I've found that the peer manager sometimes wrote specific information so many times
until the FDS storage went full.
An example data in the storage is as follows...
Hi, I'm trying to flash .hex file using J-FLash lite to nRF52840DK board using P18 Debug In (by SWD Interface).
I'm aware of pin out of J-Link Plus for SWD from https:/...
