To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
We have a Gateway based on mediatek MT7688 MIPS 32bits architecture CPU, and we integrate an nRF523832 chip to acquire BLE packets.
The gateway uses OpenWrt OS, and...
Hello Nordic!
I'm developing with sdk15.3.0, s340, and nrf 52840.
My custom board had buzzer and back-light so I need to use PWM.
So I tested pwm library example in...
I ran across something unexpected during development on our custom board today.
I checked the behavior on an nRF52840-Preview-DK board and was able to reproduce it:
This...
Using two nrf52840s and a raspberry pi3, we are going to do mqtt communication.
I want to use raspberry pi3 as a broker and use nrf52840 as a subscription and issue.
What...
Hi Great support team:
Currently our client found their product lost packets of CTF profile at outdoor, they are trying to figure out if it is related by RF signal strength...
I have a question about PeerManager.
SDK: 15.3.0 example: ble_app_multirole_lesc (I changed the source from the sample) using device: EYSHJNZWZ (nRF52832) connection device...
Hello Nordic!
I'm developing with nrf52840, s340, and SDK 15.3.0
Sometimes, I got an error in app_error_fault_handler.
This is information that gives me in app_error_fault_handler...
Hi DevZone,
I am developing an application that needs to use UART communication with the nRF52840 pca10056 board.
I am using Segger Embedded Studio V4.16
I checked...
Hi everyone
I setting my nRF52832 is central and iPhone(iOS 12.3.2) is peripheral and using "ble_app_uart_c(SDK15.3.0 s132 v6.1.1)" sample program. I print the debug message...
I want to mask ble interrupt（only ble interrup other is work）for temporary time and then to enabled ble interrupt ?
how to do it?
thanks for everyone answers!
Out of 10 prototype boards, we have 3 not working well due to 32 KHz xtal issue.
7 units are OK, but the other 3 units works only when configured with internal RC osc. ...
Hi,
I have been hired to migrate an NRF51 project that has S310 to an NRF52 one on S332.
I have looked at the migration guide in detail and had some follow up questions...
Hi I am having a hard time implementing DFU using SDK12.3 / nRF52832 now. I have tried so many times, but have failed a lot and have left a log similar to the next one in...
Hi,
I am using v0.4.0 ncs sdk.
I added following in the nrf9160_pca10090ns.overlay file
I added following in the prj.conf file
I added following in the...
