I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hi,
I'm trying to use the python bindings for pc-ble-driver with an NRF52840 dongle and I'm having trouble flashing the connectivity FW. I've used the bindings with...
I built the secure bootloader UART project without changing anything and I cannot program it using nRFgo Studio. It says:
This hex file has data in SoftDevice region. Try...
Hello,
I'm trying to use the Arduino BNO055 shield with PCA10040. This should be quite easy....but it doesn't work: I can't get any acknoledgement. Arduino use 5V pins,...
Hello,
I habe got a nRF52840-Development Kit. It is Herdware Revision 1.0.0.
While going through the Getting Started i find that the LEDs do not flash and that i have...
Just a heads up for anyone who bumps into this and is scratching their head. If you have ninja version 1.9.0 installed your build may hit an error with messages like this...
Hi everybody,
we have a remote control based on the nRF52832 and are experiencing a wierd issue with notifications.
We are using a custom 6 byte payload keymap characteristic...
Hi all, I use NRF52832.
I have a problem. I want when I connect to my chip and bond. After bond success, I insert new service. And when I disconnect from my chip, new service...
On page 69 of nRF52840 Product Specification 1.0 4413_417 v1.0 / 2018-03-16:
The table in section 5.3.6.8 shows that the WDT is NOT reset from a Wakeup from System OFF mode...
Hello,
We have an application based on ble_app_blinky that is actively scanning for advertised packets but does not attempt to connect. We have a second application based...
Hello,
i am using nrf52832. i am using 8 different pin as a 8-bit parallel port.
in my process i have to read each bit from each pin then converting those bit into byte...
I am using an nRF52840 DK. The software I have in it is emulating an NFC Type2 tag and is implementing a BLE peripheral.
When the device starts up everything works as expected...
Good day!
In SDK 12 I read values using this code:
and handle value in ble_evt_handler:
This works fine, but using SDK 15 this code crashes with fatal error...
This application uses a Rigado nRF52840 module to collect SPI data from 2 peripherals in slave mode. I have been unable to get the SPIS example running in the target board...
