We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hi, I am working on SDK 15.0 Multilink central and Multi peripheral
Soft device: 6.0.0
Segger IDE
Application overview :
When the central request to all peripherals...
Hi, I have seen in other topics here that it is not possible to control the server of the light switch example from the Android App, only the Generic On Off Model. But when...
I am working on RTLS project using nrf52832 SOC. In beacon mode i want to advertise temperature and battery strength . but i am not sure if what method should i use to measure...
Hi,
I am using nrf51822 in my project.So we are using keil5 u vision project and sdk 12.3 version so here the problem is i have imported the example program from the sdk...
The nRF52840 supports 2 Master/Slave instances.
Is it possible to configure the nRF52840 as a Master when connected to an I2C bus that has another Master present?
SDK 15.2, S132 6.1, nRF52832
I have a characteristics to write data to a peripheral, using variable length up to 507 bytes and authorization.
Writing to the peripheral...
I'm using nrf_fstorage_wrile() which work fine on most of the cases, except for len == 6 bytes. When I read back on the Flash, after successful write, I found that only 6...
Hi,
It‘s great thing that the nRF9160 DK can buy.
But there are few question need to be confirmed?
1, I saw the "Onging ceretifications" ( https://www.nordicsemi.com...
Hi,
I am using a nRF9160 with the LTE-M modem firmware. But I want to change it to the NB-IoT firmware. I have followed the instructions to install the dfu.
But when I...
Hi
I am looking at the file
\examples\light_switch\server\light_switch_server_nrf52840_xxAA_s140_6_1_0.emProject
and in there I see that there is the line
linker_section_placements_segments...
Hi,
We are planning to develop an IOT device using the nRF52840 which will communicate with a Hub device which will contain another nRF52840 chip, so we want to check the...
Hello,
I am compiling with encryption implemented for Bluetooth communications. Specifically with code taken from the ble_app_hrs_c example.
I am seeing this error:
...
Hi Sir
I am testing nRF52840 product with CMW500 BT5.0 testing script. But the testing is easily stop due to connection broken, especially for RX and long range testing...
I made an application based on ble_app_uart example using s130_nrf51_2.0.1_softdevice.hex and I have 2 boards:
- 1 nrf51DK
- 1 target board using nRF51822-QFAA H0 (version...
