We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
When I use the battery to power on, I get NRF_POWER-> RESETREAS = 0x00010000. I check the register manual to see that it is GPIO wake-up. But I didn't configure GPIO wake...
Hello,
I am using Samsung Galaxy Tab A (2016) with android version 5.1.1 build LMY47V and I can not connect to the bluetooth module at all. In the log of the nrf Connect...
For an ADV_IND advertising event without any Scan Requests, what is the maximum amount of time that the radio's receiver will stay on?
Is this parameter configurable?
...
I am trying to configure SPI with BLE using softdevice S130. But SPI is not working properly when I used it with BLE, although it is working fine without BLE
Hello Nordic,
I am having problems getting the PPK to work with my nrf520840-DK application. I am happy to share my code with you, but first a hardware setup-description...
Hi,
Do you have an example in how to upgrade the firmware of the NRF52 family through UART via IAP? I am keen to update the FW of my product without the necessity of using...
Hi,
I'm developing a central application and I would like to be able to get the full device names of the peripherals I connect to. I know how to get the device name from...
Hello,
I'm using the nRF9160 DK for a datalogger with LTE capability, and I'm using the Arduino shield "Mux Shield II" which can be found here: mayhewlabs.com/.../mux-shield...
Hi
I am using pca 10040 and nRF5_SDK_15.2.0_9412b96
Is there a way I can modify the LOG feature so it comes out on a UART instead of the USB COM port. This is probably...
I'm trying to connect to the Internet from Android Things connected to an NCP through the OpenThread Border Router.
1 Raspberry PI running RaspPi_OT_Border_Router_Demo_v2...
Hi,
I have the need to wait a few ms, from 1 to 20, in several parts of my code and I was wondering what's the most energy efficient way of doing it. Notice I don't need...
Nordic released nRF52811 to support BLE5.1 direction finding. But how to find external IC that related antennas supporting direction finding? If you have specific external...
I am using the nRF51422 board with the SDK 11
I am trying to build the following example: ble_app_hrs_adc_battery_measurement.
repository: https://github.com/NordicPlayground...
I am using the nRF51422 board with the SDK 11. I am trying to build the ble_app_hrs_adc_battery_measurement from the NordicPlayground/nrf51-ADC-examples repository. The README...
