We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hello,
is it possible to alter examples from the SDK 15.0.0 to force a BLE 4.2 connection, even if both devices are are compatible with BLE 5?
I konw that BLE 5 is backwards...
Hi there,
I am trying to automate the ADC sampling in a regular way.
Application timers seem to be a bit irregular if I depend on not loosing too many miliseconds on each...
Hi,
I tried looking over the docs but I could not find anything specific to my question, which bytes in the NRF_FICR->INFO.VARIANT contain the hardware version ID? e.g....
Hi
I am using nrf52840 Ble_App_Beacon() for advertising Beacon. so, i want to consume my power more down for battery life.I expect the nrf to go to sleep mode after advertising...
Hi
Could nRF52840 - USB Audio run on Android system?
We tested it on Samsung and ASUS Android phone then got it fail.
Please give me a comment.
Thanks.
BR
Atl...
I wrote a code using ble_app_uart peripheral example of sdk 11 for nordic nrf52832 development board.
We are making our custom boards where we are using Rigado BMD-300,...
I am trying to set the Memory protection bit and PinReset configuration with OpenOCD. I have applied the NRF52 patch (outlined here: devzone.nordicsemi.com/.../ )
I am...
Hi
I wrote the SoftDevice(s132_nrf52_6_1_0_softdevice.hex) with nRF go in the following procedure.
Erase terget.
Writting the SD
In the Log area, it is indicated...
Hello,
I have just got a brand new PPK board, and would like to use it with an external J-Link. As far as I could tell by reading the documentation , this scenario is not...
I am working on the nRF52840 DK and nRF52 SDK 15.2.
I can run the USB CDC ACM example and the USB Audio example successfully.
Is there a way to create BOTH devices at...
My code compiles and runs fine in debug mode with logging turned on.
In Release mode, it builds and runs fine with logging turned off, but if I turn logging on (i had an...
Hello,
I want to create an application for the nRF52832 using Segger Embedded Studio and the nRF-SDK. In order to have a clean and portable solution I would like to have...
OS in development environment ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex?-M4F 32 bit processor...
I'm using the UART / Serial Port Emulation over BLE example on the nRF52 development kit connected to a custom microcontroller.
I just need the nRF52 to simply relay bytes...
