I'm reading the source for the nRF Toolbox app for Android 4.3 and comparing it to the Proximity Profile spec from the Bluetooth SIG, which has this to say about path loss...
Hello,
I have downloaded the software related with the "nRF51822 Bluetooth Smart Beacon Kit" in order to modify typical iBeacon's parametres such as UUID, Major ID, Minor...
Hello,
i would like to know if the new SoftDevice 130 for the nrf51822 is compatible with the DFU OTA bootloader example provided in the SDK (nrf51822/Board/nrf6310/device_firmware_updates...
Can I get uuid of central device from peripheral device(nrf51822) ?
I want to check out which smart device is connected.
May be I can tell central is iphone4s or iphone5...
Recently s110_nrf51822_7.0.0 softdevice has been released. I cannot find specification where those new amazing features (they are impressive, indeed :) ) are described, so...
When I am using power manage function to keep device low power mode, for every 6 milliseconds I am getting small spike of ~300 micro Amp and average current of 300 micro Amp...
Hello Sir,
I’ve been used nRF24L01P controlled by DSP to transmit and receive data for few months. The nRF24L01P is run in 1Mbps mode. The SPI of DSP is set to send 8 bits...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hello,
I have read a lot posts which has the same title unfortunately I am still unable to solve my problem. I am using pca10028, s110, SDK 6. Code is based on BLE_app_uart...
Hello,
on my computer I have the IAR Workbench (8.11) installed.
I want to start Bluetooth software development.
Therefore I installed nRFgo, unzipped the nRF5_SDK_14...
Hello
in sdk14.1 in examples/ble_peripheral/ble_app_buttonless_dfu i get this error when compiling with g++:
make[1]: Entering directory '/home/work/software/nordic/sdk...
Hello,I want to make NRF_LOG_BACKEND_UART work with NUS . The nus work with app_uart_fifo,and the NRF_LOG_BACKEND_UART work with app_uart. I try to make them work together...
I am using NRF51822,S110,16Mhz XOsc. In this if Controller goes to sleep mode the current consumption is 4.9mA. In my application at sleep mode BLE should be connected and...
If I make a product using the nrf24lu1+ chip how can I register a PID for it? The VID is 0x1915 and I know that Bitcraze uses a PID of 0x7777. The Linksys WUSB11 v2.8 802...
Hello
We have nRF51822 chip on our board. We want to make next version of the board. But heard that nRF51822 will be no supported in the near future. So the question is...
Hello,
I am having an issue with my SAADC, it seems to hang while calibrating. The flow of my app is as follows, on my main the SAADC is started with saadc_start() , where...
Good morning, I want my nRF24LE1 to sleep & wake up (memory retention, timers on) while retaining data in xdata, but it's not doing so. Please help!! Thanks, Mahesh
...
I want to keep the value of the variable even if there is power interruption or reset in the system. That's why I want to create persistent variable in main. Do I need to...
i use ble_uart example nrf51 in sdk1 with ic kline interface with mortorbike
NRF51 Tx,RX connect to TX,RX MC33290 and Kline of MC32290 connect to motorbike
( you can Google...