Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
Hello,
I have a problem with Indicate Characteristic. When I try to send data using sd_ble_gatts_hvx() function, it always sends 20bytes from address 0x00. This is my code...
I am trying to run my program once per second using timer. The timer is initialized as follows:
APP_TIMER_INIT(APP_TIMER_PRESCALER, APP_TIMER_MAX_TIMERS, APP_TIMER_OP_QUEUE_SIZE...
I'm trying to figure out how the bonding works in the multilink demo. It seems like the central device only goes through the bonding if the peripheral has the multilink service...
ble_app_uart_s110_pca10028_nuevo.uvprojx
Hi, I´m using a nRF51244 with s110. I program it in nRFgo Studio (s110_nrf51_8.0.0_softdevice.hex)
I try turn on the passkey...
Hi,
I performed an OTA update of my APP. (SD 7.0 and BLE single bank bootloader were flashed).
The update finished without an error and then my application even starts,...
Hi,
I'm developing on a custom nrf51822-based board, and using the s110 softdevice, version 7.0.0. With JLinkGDBServer and the toolchain's gdb, I can debug softdevice-less...
Do you have a BLE SOC chip that can behave as a master and a slave, and also has embedded stack so no host processor is needed. I am looking for a chip that can be used in...
hi,
Inorder to flash the softdevice to evaluation board PCA10024 , i tried using nrfgo studio as mentioned in the user guide.but the nrfgo studio does not show any board...
Dear all,
I am using SDK7.1 with S130 v0.5 alpha. Can I use the DFU example in the SDK6.1 to update my firmware in the chip(nRF51422)? If not, is there any alternative...
I am using S110-based peripheral device which is sending 20byte notifications. Application on my peripheral works fine (testing with MCP gives transfer rate about 15kB/s which...
Hi,
I was using nRF51DK with Keil uVision ver 5.14 and SDK 8.0.0. It worked okay yesterday and I tried HW peripheral as well as BLE peripheral.
But today it doesn't...
Is it possible to identify a device as a previously bonded peer based on the advertisement package and before establishing a connection?
I would like to be able to bond...
Hi
Im using nrf51822 board from RedbearLab. SDK6.1and SD7.1.0.
I added DFU to my application and iam able to update the firmware OTA.
My issue is after adding dfu...
Hey there,
I am looking for the right pin out to wire up a reset button to my board so that I can reset the IOS device is paired to. Can some one help?
Tyler
