I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
I am a student currently studying BLE.
At present, I am working on a multi-connection setup where both the master and the slaves are using the nRF52832. Specifically, I...
Greetings starting from the 'ble aggregator' example I developed a BLE central on NRF52840 with NRF5 SDK 17.02, capable of managing multiple peripherals which, once connected...
I'm running SDK 2.8 and 2.8 Toolchain. I created the sysbuild.conf setting:
SB_CONFIG_BOOTLOADER_MCUBOOT=y
and put it in the application folder (per this support request...
Hello, I am relatively new to the nRF 5340 Audio DK. I recently ordered a singular nRF 5340 Audio DK board and my goal was for the board to take in input audio via the PDM...
Hi all,
I've been using the nRFConnect extension without any issues, successfully connecting to my nRF5340 board via JLink, flashing firmware, and receiving printed messages...
i get the following build error whenever i build for boards other than nrf
- CMake version: 3.21.0 -- Found Python3: C:/ncs/toolchains/b620d30767/opt/bin/python.exe (found...
Hello,
I encountered a compilation issue when using the app_timer function. The error message is: "'TickType_t' undeclared (first use in this function)". I believe the problem...
Hi,
I am trying to set the VDD pin to 3.0V instead of the current 1.8V (also changing the GPIO voltages to 3V). I've seen many questions related to that but no solution...
Hi Support Team
May we know that the difference between Engineering Build Code BB0 of nRF54L15 with normal Build Code? Which is recommended for the mass production of customer...
Hi, I am using nrf9151-DK to send and receive data over UDP protocol. Firstly, I tried to use AT commands to send and receive meassages as described here , I had no isuues...
Hi,
How can I control a Thread CoAP Client, which is connected to a thread supporting modem such as eero+ (in other words, the CoAP client is connected to the internet)...
Hello
I am trying to build the Zephyr mesh distributor sample on the nRF 52840 dongle
It builds and runs just find on the nRF52840 DK
But when I try to build for the...
Hello,
I'm looking at adding USB DFU to my project, (Not USB DFU recovery in the bootloader, but in runtime) and was trying this example. It fails to build for the nordic...
Hi,
im develop a keyboard by ncs sdk in nrf52840,and one funcation is that power off/on the keyboard ny fn key .i see the CAF: Power manager module , It doesn't seem to...
