Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hi,
I am trying to retrieve data from server using HTTP GET request, using AT command for Serial LTE modem application.
So, I can connect to the server using AT#XHTTPCCON...
I have a hardware like the PINE Watch, with nRF52832 and external memory XT25F32B connected via SPI with the following:
PIN P0.2 SCK
P0.3 MOSI
P0.4 MISO
P0.5 CS
...
I am developing my own low level radio protocol based on BLE advertisement telegrams with the nRF52840. It works good so far and the usage of SHORTS helps a lot.
But there...
Excuse me：
1、 I can't find the USB DFU example of the nrf52820 in the SDK.Does nrf52820 support USB DFU？
2、52820 needs to Implement USB OTA ，enumeration as keyboard...
Hello,
I'm trying to include a byte in the advertised data that indicates on which channel the advertisement is being sent, 0 = channel 37, 1 = channel 38, 2 = channel 39...
Hi,
We have a board with an nRF52840 working as the primary MCU which controls an nRF9160 via AT commands.
P109 from nRF52840 is connected to the nRESET of nRF9160. To...
Using the GPS sample application as a base, I examined the behavior of "concurrent" cellular and GNSS. I enabled cellular with at+cfun=21 after a GPS fix was obtained. I also...
Hello!
I'm currently working with Zephyr on a custom board based on the RAK5010 board. This board (RAK5010) is currently supported by the Zephyr project,uses the NRF52840...
Good day i am new to Nordics platform and SDK also new to segger embedded studio
i am required to develop a solution that receives data on the UART of the NRF52840(client...
Hi,
I have PCA63511 Power Profiling DK and nRF52840 DK ( and nRF9160-DK )
I was using SoftDevice SDK, and no issues with measuring nRF52840 device. But now I switched...
As state in the title I am trying to run pc-ble-driver on nRF52840 Dongle running examples on Mac OSX.
I uploaded connectivity_4.1.4_usb_with_s140_6.1.1.hex file on my dongle...
Dear:
Do you have any cases about wireless serial port printing debugging at nRF52832 BLE device ？
When the device is not connected to the debugging line, the dongle can...
Hello everyone,
Im developing a simple BLE scanner and its purpose is to receive and send beacons data by serial port.
My application worked quite well when flashing to...
Hello,
I have been trying to debug a curious behavior leading to higher energy consumption (~17mA) on my Sleepy End Device (Rx is off when idle).
I am using the nRF SDK...
