Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
I'm new to NCS, and playing it with nrf5340 pdk kit.
My problem is ,I can't play any projects, all of them go to the same error: cmake failed,create_nordic_project.py failed...
Hi,
To support the large and dense networks we are building, I need my network coordinator to be able to throttle OTA packets to not completely overtake the network’s bandwidth...
Hi,
I want to create a mesh between my nRF53 DK and dongle. For my project, I created my own service to send accelerometer value to the client (mobile application). Now...
I am developing an application that sends an image with BLE to an android phone. It is remarkable similar to the Image transfer demo ( https://github.com/NordicPlayground...
Hi
I am updating from Softdevice 6.1.1 to 7.2.0 and have issues with nrf_sdh_ble_enable(..), My setup is:
NRF52840
SDK 17.0.2
SoftDevice 7.2.0
Running FreeRtos...
Hello,
Sorry for this long question but these questions are bothering me and I need these to carry on with my project.
1) What is the peer manager's device identity list...
I want to use nRF52840 USB dongle as mesh server device. I have tried several links but not success. Please provide me hex file so I can flash using nRF connect desktop app...
Is there a way only from the analog input where measure the battery voltage to distinguish that battery is charging?
I am short on IOs and will be quite a challenge to find...
Dear all: Recently, I was debugging nrf52805 by custom PCB, using sdk17.00, I enabled PWM, frequency of 4kHz, to drive 4kHz passive buzzer, encountered a problem: The buzzer...
Hi,
I'm having problem using SPIS on nrf9160. The data/clock from master looks clean on scope, but 91 is not receiving the data. Interestingly, when I connect a debugger...
Dear,
We would like to have a setup where we want to measure the current consumption of a battery-powered device with an NRF-52840 chip:
The battery is a Li-Ion one...
Hello together,
I am try to get the asset_trecker_v2 to work on my thingy 91. When reading the debug log in LTE Link Monitor I see the warning:
So I downloaded the latest...
Hello, the chip I use is nrf52810 QCAA, when I use j-flash lite to earse the whole chip, it success, then I program the flash_s112_nrf52_7.2.0_softdevice into the chip by...
I am trying to merge the following projects:
SDK versions: 17.0.2 and 5.0
I have taken the contents of the mesh example sensor/server and merged it into the ble_blinky_example...
I created .c file, and add a few TWI functions to it. However, when I run the code in segger, all functions in the .c file shows a "multiple definitions of xxxx" error (see...
