Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
We are using powerdown() function to put the procesor in sleep mode for the said time
We are facing following difficulties
1. It does not work if we use nrf_delay_ms(...
Hi there,
I am developing a product using the nRF52833 QFN40 package (nrf52833_qdaa), and have the nRF52833DK for testing which uses aQFN-73 package (nrf52833_qiaa). I am...
Hi,Master:
Question：
When the finished product cannot be debugged with jlink, I want to save and trace the function stack information through the firmware. When there...
Is it possible to merge client and server to one image using ble_uart Example?
Which could work as client ,also as server ,it controlled by program.
Thanks a lot.
Hi,
I'm using the NRF52811.
In my schematic, the SWDCLK and SWDIO is connected to an external connector and the NRF52811 is connected to MCU through the SPI channel...
Hello
I'm having problem with UDP reception. I'm using nrf9160 with modem firmware 1.2.3, nRF Connect SDK v1.4.0, LTE-M.
I can receive UDP packets in the device as long...
Hi I am designing an intercom and I need help related to it. The following are the requirements of my project. I need an intercom module through which two-person can communicate...
Hi
Now I have a PCA10040 board and MDBT42Q board. I intend to transfer data between two boards via ESB TX and ESB RX example. However, with MDBT42Q I used nRFgo Studio to...
Hi,
We would trigger button to send zdo_mgmt_leave_req to coordinator for leaving the group.
When coordinator is not on power up, we would receive the 0xFF at callback...
Hi,
I want to calculate throughput rate using data that nRF52840 dongle working as sniffer captured.
Wireshark shows 'time' , 'delta time' and 'packet time'.
I think...
Hi,
I have serval questions about TX power settings.I wan to increase power to +8dBm,but the result is no effect.
1 Before reseting Tx power,call nrf_802154_tx_power_get...
Hi There,
Custom xamarin bluetooth app [using Plugin.BLE] is failing to connect to the device using ConnectToKnownDeviceAsync approach. User uses tap-to-pair and tries to...
Hi ,
We have a requirement to use the end device. The device should be an sleepy end device normal . When we want to transmit a large data to router , we want make this...
Hi Sir:
I am using SDK nRF5_SDK_17.0.2,the chip is nRF52810. Using the ble_peripheral\ble_app_uart.
The IO is using P0.6 as the BLE Uart's RX Pin,And P0.7 is used as BLE...
