Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
When building the sample code using the latest SDK I do not see the device in the device manager and after a while I get this error:
Any hints on what is wrong ?
...
I have already made a post for this problem. Initially, Amanada Hshei gave some troubleshooting techniques and it did not work out,
Here is the original post, and My request...
Using Windows 10
Master Branch
Compiled using Segger 4.16
Downloaded merged.hex
When running NRF Connect Link monitor and connected to nrf9160
I receive the following...
HI,all
I have tested ZC and ZED to establish network,I found a method zigbee_erase_persistent_storage(bool),when i put true on ZC and put false on ZED, first time they can...
HI,all
I am a newman for zigbee on NRF52840 with S140 softdevice,
I have two board, one is ZC and another is ZED.
On ZC board, I use ZB_GET_OUT_BUF_DELAYED2 to send...
I am using sdk15.2.0 with PCA10040 dev board.
In ble_app_eddystone example, the configured advertising interval and duration dont match the observed values.
I think I...
Hi Nordic,
I have recently received an error from pm_init that I have never seen before, NRF_ERROR_INTERNAL. After some debugging, I found it was really due to NRF_ERROR_STORAGE_FULL...
Hi,
I am using NRF MESH SDK V3.0 ,nRF5_SDK_15.2.0 and with s132_nrf52_6.0.0_softdevice .
I've noted some problems when i try to use the app_timer in repeat mode with a...
Hi Team,
I transplant the project Uart from example/peripheral/uart tranplant to blecentral/multilink project, but it does not work, it indicate that APP_UART_COMMUNICATION_ERROR...
Hello,
In below link, I am bit confused between “With bootloader” and “Without bootloader”. What for this bootloader.
https://infocenter.nordicsemi.com/index.jsp?topic...
Hi all,
I purchase a Li-Po batter where it will output 4.2V when I connected to nrf52480 DK, it causes all 4 LEDs (LED1, LED2, LED3, LED4) not functioning anymore.
The...
Hi,
I have the latest 0.4.0 tag, flashed the latest modem firmware 0.7.0-29.alpha, and debugging the asset_tracker app under nrf9160_pca10090ns.
When I debug the app it...
Hi,
I'm using the latest everything for the nrf52840 with SES.
When I define a global variable that require substantial memory I get the linkage errors:
. bss is too...
Hi
I want to run the the HTTP application update sample on the nRF9160. SDK v0.4.0, SES V4.16, Win 8.1.
I can build and run the application on the DK but I don't find...
