Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
hi team,
i have downloaded image transfer demo source code in github. installed it in sdk 13.0. the softdevice is 5.0.0-2. i am using nrf52840 pdk. the code is successfully...
Hi Al
I'm implementing multiple channel ADC with PPI
sampling multiple ADC channels with PPI, adc event triggered adc_event_handler as many times as channels (instead...
Hello everyone. I'm working to a project with nRF52840. I'm developing the code in SDK in SES ide. The task i want to perform is transfer data from the memory of nRF52840...
Hi,
I am using the S130 central pairing to just one peripherial at a time. Upon power up after hard/soft reset, the central connects to my peripherial just fine, transfer...
Hello,
We are using the Segger Embedded Studio and trying to flash the blinky code on our nRF52DK. We have seen many videos but are unable to make it work. The code gets...
Hi,
In my memory usage, I see 780KB free from 1MB of flash. That means I am already consuming 244KB of flash when my code size is only 77KB. Obviously, there are other registers...
I have been trying to flash my nrf51822 by waveshare using my nrf 51 DK. I have been making the following connection. I am currently using P20 as the needle adapter for P19...
Dear Nordic Team,
Thanks for supporting.
Now i am try to interface(TWI) MMA8453 with nRF52810. Already i am worked with nRF52832 its working good. If possible for interface...
I tried to add a BAS service to a project with an LBS service (ble_app_blinky), but I cannot complete the services_init() procedure for both services.
Is it possible to...
Hello,
I would like to kwno if it is possible to get information about the hardware in my main application. NRF_DFU_HW_VERSION is stored in the DFU and is used to verify...
Hi all
I want to stream data from various nRF52 objects to a single Android smarphone.
I have no problem in evaluating the throughput of each nRF52 device to the client...
Hi,
I want to set up a demo bike speed and cadence transmitter. I am using \ant\ant_plus\ant_bsc\bsc_tx source code. However, I have plans to use BLE at the same time...
Hi,
Are softdevice's api calls thread safe (specifically speaking sd_ble_gatts_hvx ()) -
i.e. Will a concurrent call to sd_ble_gatts_hvx () from several threads corrupt...
Hello All,
I am working on nRF51822 use IAR nRF5 SDK 12.3.0.
I am trying to debug the DFU in IAR. At that time i got an error show below
I use IAR version show...
Hello Nordic, I worked in a project and there a used NRF52840-QiAA-R. For this PN , I need the latest REACH and ROHS , Compliance Certificate. Where I can download these certificates...
