Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hi,
I would like to check battery level using the SAADC of the nrf52840.
Assuming the voltage is less than 3.6V, do I need to have a resistor between the battery and the...
HI,
I am new to IoS development with NRF.
I am having NRF52840 DK, IoS device. I want to implement USB HID device application (similar to pulse/Gluco meter ) on IOS. I...
Hi,
I am not able to compile the SDK example by using SES for ARM V3.52.
I got one error which shown below:
It pointed to the link ldr r0, =%4
Thanks
Gan
Hi,
I am using fatfs of nRF5_SDK_15.0.0_a53641a.
I am writing a program with keil.
I am currently doing SPI communication with BLENanov2(nRF52832) and SD card with...
Hi,
I am implementing the UART on NRF52840. TX works but the RX doesnot. While debugging, I noticed that STARTRX task register is not getting set due to which the RXDRDY...
Hi Sir
We'd want to do RX testing with DTM mode, however, the dtm example code looks can't report receive data or total packets counts,
So that, we don't know how to determine...
Hello,
I'm using the nrf15822 chip and am using the ble_app_uart example from nrf5_sdk_12.2.0.
I know softdevice will automatically generate random numbers through RNG...
I've been told due to PAN 58 it is not possible to use EASY DMA with nrf52832 without switching to the deprecated SPI driver. Is there a workaround that allows the use of...
Hello,
We are going start custom PCB design by using nRF52840 chip and SDK 15.0, but confused for use 3rd party nRF52840 modules or design complete custom PCB using componenets...
Hi,
Despite knowing a fair bit of the theory of wireless comms (mainly PHY and MAC), I'm brand new to actual hardware configuration/protocol development, so please be gentle...
As a master device with a whitelist there is a limitation on how many slave devices can be connected. If i am correct, other than whitelist there is no restriction to the...
Hi,
How do I receive data from host (computer) on my BLE device(Nordic board)? I want to use a simple open source HID API to send data to Nordic board and glow an led or...
Hello, we have finished all prototyping with BLE modile from Taiyu Tuden, this module: https://www.yuden.co.jp/wireless_module/document/datareport2/en/TY_BLE_EYSGJNZ_DataReport_V1_9_20180530E...
Good day, I am new to this forum so I am having some problems posting my question. Sorry for any inconveniences. I am having serious problems flashing my custom NRF5282 board...
I want to connect nRF52832 with PC. The objective is using nRF52832(I am using BT832 Module) I have to scan all Blue Tooth deceives details and send to PC. Please help with...
