Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hi,
I use library NRF21540.c to config to control NRF21540, to amplifier the radio of nrf52832.
This is my define:
#ifndef NRF21540_USE_GPIO_MANAGEMENT #define NRF21540_USE_GPIO_MANAGEMENT...
Hello!!
I want to implement I2C between nrf52832 and capsense button (CY8CMBR2110-24LQ) and want to put it to sleep mode so that I could get ~2-3uA if there is no activity...
Device: nRF52840
SDK: 16.0.
Softdevice: 6.1.1
Hello,
I'm using Timer 2 peripheral using simple timer driver. It's working fine but I have serious drift/accuracy issue...
I use SDK16 and softdevice S140. I use cdc_acm to simulate a UART port. My data traffic is very heavy. It cause data overwrite and send out many zero. My source code snippet...
Hi,
I have been trying to use nordic nrf52840 USB dongle/ pca 10059 in BLE mode to fetch data published through Bluetooth; however I can find any compilers that support...
I have adapted the example ble_app_gattsin SDK_17. My code is as follows:
However, an error is thrown when setting the scan filter as follows: nrf_ble_scan_filter_set...
Using app_usbd_cdc_acm_write method as blow: I see following output in Putty.
Baudrate is correct (115200) + it decodes first part of the message.
I have no idea why...
When I try to program custom NRF52 board using a J-Link v9 (It's probably a copy product), I'm getting the error below. I also have several NRF52/NRF53 DK boards when I try...
More than once I have started to develop a module based on an SDK example project only to find out that it uses deprecated code and drivers, so then I have to update my code...
Good morning,
I'm developing an application for nRF52805 using NRF5 SDK.
I have successfully integrated FreeRTOS into the example application.
I would like to add CMSIS...
Hi,
I have a question about the behavior of the Softdevice S132_nrf52_7.0.1 for the nRF52832 in case of the reception of an advertisement packet of type ADV_NONCONN_IND...
Hi all,
Would like to know that is there anything that is similar to TrustZone, which the key is not hardcoded in the application program, installing the key file like...
Hi we currently have a product develeped for 52840 on basis of old sdk 15.3. We are just about to start a new development based on 5340 for which we are required (and want...
Hi Experts,
Recently, I am developing the mesh project based on the latest nRF mesh SDK, everything is running well. But I encountered one issue, that is how can provisioner...
Hi,
I've followed the instruction from " Developing for the nRF52805 with nRF5 SDK" to port the example "blinky_freertos" but I got the following compilation error:
This...
