We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
I have two nrf52 chips connected to each other via SPI
I send data from my Nordic Uart app to my nrf52 chip 1 and I want to send the data that I receive from Mobile app...
Hi,
I'm trying to prepare the firmware for a nRF24LU1+ in order to allow automatic driver installation on Windows.
Based on Microsoft documentation during device enumeration...
I like to provision a node in mesh with the help of computer. Shall i use serial example? Is it possible to use without interactive_pyaci to provision a node with computer...
Hi,
My questions is related to this one: https://devzone.nordicsemi.com/f/nordic-q-a/58250/short-range .
We are also developing board and range is shorter than in smartphones...
Hello!
Does anyone know of a library for the I2C LCD 16x2 display? I found the library by lovee, https://devzone.nordicsemi.com/f/nordic-q-a/23401/nrf52832-connect-with...
I encountered an issue, please kindly refer to the attachment for the detail.
"'' The problem is: a> Run demo on PCA10056 (BLE adv & ANT continuous scan). b> ANT Dongle...
When trying to configure custom UUID the nRF Connect, the program fails to find the location of the file.
This is due my username to be "Filipe Aguiar" with a space which...
Hello, Nordic community,
I built and successfully run mqtt_simple project on our MQTT broker using v1.1.0 firmware and NCS.
I edited CONFIG_SERIAL=n in spm and mqtt_simple...
I have one of the nRF52840-preview-dk boards. When I brought up nRFgo and clicked on the board, I was invited to update the JLINK firmware. It was pretty enthusiastic in its...
Hello,
I'm trying to use the zephyr settings module to save bluetooth settings on the nRF9160 DK. I'm using the NCS downstream version of Zephyr . Unfortunately in the most...
1.when i use the example on the dir : examples\ble_peripheral\ble_app_blinky\pca10056\s140\arm5_no_packs
i have sucess flash the softdevice and the app:
the console show...
Hello ...
I'm adding buttonless DFU support to my nRF52810 application using the instructions here . I'm using SDK 15.3.0, SD 112 6.1.1.
First question: These instructions...
I'm using the SPI Manager to send large transfers of data to a graphics controller. What I see is that, once a single byte is transferred, the CS line will continue to pulse...
Hi,
Greetings!
I want to disallow an unknown bluetooth device (like phone, etc) to connect to "secure_bootloader_ble_s132_pca10040" except from a bunch of pca10056 (central...