Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hello Nordic
My device is consuming ~4mA in normal (I already use function "sd_power_dcdc_mode_set(NRF_POWER_DCDC_ENABLE)" )
As i know that the current SDK mesh v2.1.1...
Hi,
We are working on Android O with SR3 v1.1.
There is an issue that our Android STB can't find any BLE device using your library.
( https://github.com/NordicSemiconductor...
HI
[environment] · NRF 51822 · SDK 12.3
We are developing application software including DTM.
In the application software, a flag to start DTM using FDS is written in...
Hello all,
I've recently started developing an nRF5 device (using Segger on Ubuntu, and SDK15.2.0), and for what I have read regarding peripheral drivers, I should be...
Hello all!
I'm trying to optimize power consumption for project based on nRF51802 and external host MCU. My current platform and toolchain:
1. nRF51802 as Bluetooth controller...
Hello, i am using NRF52840 board with NRF52840 SDK version 15.2 with softdevice 140 Version 6.1. I am using the BLE_NUS_UART_C example and id like to send a scan request to...
Dear nordic,
BLE advertising happens in 3 channel(37,38,39) and scanner scans these channel based on scan interval consecutively
I want to scan single channel instead...
Using nRF Connect for both iOS and Android, the advertised name is the same for both apps, i.e, DeviceX.
Clicking on the device information also shows the Complete Local...
Hello,
I am using an nRF52840PDK (master) to use an SPI peripheral, where my code is based on examples\peripheral\spi. My IDE is Segger Embedded Studio and I am using SDK...
Hi Nordic Team!
Please find below attached the schematic for my custom nRF52832 proto board. The boards are already manufactured and are in the bringing-up stage. The designs...
Hi, I've encountered a problem described here: https://devzone.nordicsemi.com/f/nordic-q-a/37917/nfc-issue-when-migrating-to-sdk11 Since I could not figure out the issue,...
SDK 15.0, PCA 10056 (1.0.0)
Is it possible to let the relay-example from the SDK 15.0 run in a way, so that the long-range feature of Bt 5 is supported between the Peripheral...
Hello,
I'm using a nRF51422 uController (Custom board) with the Softdevice s130 withe SDK 11. I want to go back into the bootloader from my application after I told the...
Hello Everyone ,
By using sdk version 15 for NRF52840 I wish to connect the lsm9ds1 sensor to it and using seggar embedded studios IDE. The header files available in google...
