I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
I'm using SDK 15 on an nRF52840, compiling with Segger Embedded Studio.
I've created a project in SES using the project_template folder.
When I try to use both ESB and...
Hello,
I want to access the AIN input 6 ADC/LPCOMP input 6 to measure a current at two points with a defined time interval in between.
Since I am not familiar how to...
Hi,
I am trying to use UART in a blocking mode for nrf52840. I am able to transmit the bytes, but not receiving the bytes. While debugging, figured out that RXDRDY event...
Hi,
i have some issue regarding DFU-ing the bootloader.
Here is my command to generate zip file: nrfutil pkg generate --hw-version 52 --bootloader-version 1 --bootloader...
Dear Nordic Team:
I used nrf52832 as my BLE IC, and an IC of Novatek as my MCU. They are connected by uart. Now I need to merge ble_dfu and serial_dfu on the version of...
Errors while starting debugging session
I am getting error 65 'access violation' in Keil Uv5 and 4.
In IAR , I am getting 'User Error:Stack Pointer is setup into incorrect...
Hi,
I modiy the usbd_hid_generic example to tow endpoint by sdk15.0.When i use the USB testtool send some datas to usb deivce,the d atas cannot be read properly by NRF_USBD_EP_OK...
Hi, in our one project we are using nrf52832 radio to transmit the data packets. After transmitting the data packets, the nRF52832 chip need to disable the radio to minimize...
Using SDK 15.0.0, I have ported the peripheral/usbd example to custom hardware based on the nRF52840-QIAAC0.
In the nrf_drv_usbd_enable() function, execution hangs at
...
I'm communicating with a temperature sensor using I2C/TWI and I'm now trying to send that received data over BLE using the HTS service.
When I send a ble_hts_meas_t with...
Hello,
I am using nRF52 with ADS1292, and i am trying to sample at 8kHz with data throughput of 72kB/s, but some data is being randomly shifted giving me random spikes...
Hi Nordic Team,
I am requesting any block diagram level documentations - on a high level software architecture overview of SDK.
My goal is to understand how different...
Hello All,
I want to know Maximum External flash size supported by nrf52832 .
On which parameter Maximum size of external flash depends?
If it depends on usage, then...
Hello,
I'm currently using a bootloader based on the one included with SDK 15. We're close to mass production and I need to decide on how much space I should leave for the...
Hi,
I have designed a system that uses the SAADC to sample 3 analog inputs in scan mode at 8 KSPS, performs downsampling by a factor of 8 using the DSP, and sends the results...
