Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi,
I'm using the example project usbd_msc and I am having no luck having the volume come up on windows when I plug in the nRF_USB line. I can see "nRF52 USB MSC Demo...
We are currently getting our firmware ready to test devices for FCC and other radio testing. We have an AThost-like setup that passes AT commands from a terminal over a BLE...
.Hi Nordic Support team,
I'm using NRF52832, SoftDevice S132, SDK version is nRF5_SDK_17.1.0_ddde560.
I want to transmit 9 bytes of data collected from an I2C sensor...
Hi,
the I2C burst write function below work perfectly <16 number of bytes. Once I transfer more that this, the return code throws an error "-28" and my scope doesnt even...
Hello, I would like to develop an automated tool for our production line to use to perform DFU on our nRF52832 system. Is it possible to communicate with the nRF52 Dev kit...
Hi, I developed a custom board and I am able to toggle other IO pins but somehow pin 10, 9 wasn't working. After some research, I found that NFC must be disabled to make it...
Hi,
I am trying to set EDRx en LOG_INF the result using following code:
static struct lte_lc_edrx_cfg drx_cfg ;
//enable EDRx
LOG_INF("== Setting EDRx =...
Hi,
I have a custom board with a nRF52840 and the nRF21540 FEM. To control my FEM, I have added the following to my code to my nRF52840_nRF52840.dts file:
/ {
nrf_radio_fem...
Hello Everyone. I tried to run the ble_app_multirole_lesc example on SDK 16.0.0 to test the numeric comparison match feature on bonding. And found that the handling of this...
Hello,
I am currently updating from SDK v2.3.0 to v2.5.2 but I am not able to get the 'psa' functions working correctly (as they did with previous SDKs).
I am trying to...
Hi, How to find out what function is being called, when sw interrupt occurs? I have created a timer that should call a function. But I'm having a hard time finding what function...
Hi,
I am working on custom board which has nrf9160 as modem and stm32 as host controller.
here I am used lwip stack on stm32 controller to get the IP address.
I have...
I'm trying to integrate AES-128 (ECB mode) decryption into my project
I've based it on the AES_CBC sample, and adapted it to use ECB mode instead of CBC. When I compile...
Trying to use the nRF Connect quick start with the evaluation board and the programming fails. 2024-05-22T09:09:27.145Z INFO Initialising nrfutil module: device 2024-05-22T09...
Hi,
I encountered an issue from my custom board who are using a nrf52832.
When i place my board in very cold temperature environment (around -35°C), sometimes the voltage...
