Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hello,
So I am just real confused on how the softdevice programming works via the open_bootloader right now and can't seem to track down the documentation I need to be successful...
I'm running a code based on the ble_app_uart example using the PCA10059 dongle. I have the dongle connecting to a raspberry pi 0 W via BLE and when this runs using a power...
Hello,
at the moment I am working on a project with a nRF52840DK as central and multiple nRF52DKs as peripherals. The code on the central is based on the "ble_app_uart_c...
Do the examples in the SDK folder like ble_nus have their binaries with softdevice already? I'm a newbie in Nordic and using the BLE NUS example with nRF52-DK to learn as...
Hi team,
My customer wants to develop a system with one central, multiple peripherals, each bandwidth is <50kbps, but they want the latency can be as small as possible....
Hello,
I would like to know how can i use SPI on the radio example.
I'm using (programming) the radio example, receiver, for AoA and it's working so far. What i'm trying...
Hi,
My observations: DSP_PRESENT Macro is enabled in nrf51.h , nrf52.h, nrf5340_application.h files in v1.5.0\modules\hal\nordic\nrfx\mdk path As shown below: #define...
Hi
We are using nRF52832 with SDK17.2 and SD 112.
We are trying to make a NFC_PAIRING_MODE_GENERIC_OOB to a PC with the following System Information:
OS: Windows 10...
Dear All, I have noticed the following issue: In the beginning of my code execution pin 1.09 is high, before I can even call . From what I found in the datasheet pin p1.09...
Hello!
When using the AT%RAI=4 it works as expected for NB-IoT however it does nothing for LTE-M. It is my understanding that it should work for LTE-M. Does this mean my...
I see many questions on how to enable a timer to start SAADC conversion every period (such as 1 hour).
But never found a simple example.
I would appreciate if you can...
I have implemented a OpenThread application. The application connects to a Thread Border Router . I'm using ncs and when using version 1.4.0 everything works fine, I can connect...
Hello, I run a project in SES 4.30c with nRF5 SDK. I just got my computer updated by our IT-department, and now I get a compilation error on my first #include :-) I still...
I have a custom board with an nRF52840 that uses high-voltage mode (5V on VDDH) and the chips internal voltage regulators. This requires setting REGOUT0 to 3.3V. My firmware...
Dear Nordic Team,
We are using nRF52840 based module and using its ZigBee Radio. For one certification purpose, we need to know the max. pulse time (duration) for Tx and...
