Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hello!
Could you show me an USBD configuration example which works fine with Arduino serial monitor? Because Arduino serial monitor froze when i send a string , but when...
In the nRF52832 (Laird BL652 module) I have programmed.
MBR + SoftDevice from 0x0000 0000 Application from 0x0002 6000 ~ 0x0005 927C
Now trying to program additional application...
Hi
Is there any documentation regarding bluetooth in nRF52832 specs sheet or anywhere else? I understand that there are examples provided by SDK. But I want to know in detail...
Hello,
we are running BT certification on product with nRF52840 chip. It seems that TCRL-2018-2 is now mandatory.
Did someone know if the QDID certified TCRL-2018-2 is...
I am not able to program the nRF52840DK by copying over the .hex file generated by my project to the JLINK drive. However I am able to successfully program using Segger directly...
Hi,
We are looking at using the key:value store functionality defined in mesh_config.h. Can you provide some additional detail on
HW and or SW configuration required to...
Hi,
We are trying to develop a system of IMUs for motion tracking using multiple Thingy boards and an nRF52832 board. The Thingy boards are used as IMU sensor nodes and...
Hi, This is M.Irfan. I want to send data (collected by mpu6050 sensor) using Bluetooth in my cellphone and want to save it. Can you help me with some example code of sending...
We noticed issues regarding BLE activities when running our custom bootloader. It seems that we have located the cause but would like to have approval for that behavior. ...
Hi All
I am trying to find some example code which uses easy DMA over UART using nrf528240..
Using sdk version 15.0. The example which is available by default uses the...
Hi,
I recently bought a nRF51 Dongle (PCA10031) and a nRF52840-DK (PCA10056) and I am now trying to use it for BLE sniffing with Wireshark. I am running OS X 10.14.4.
...
I compiled 4.0.0 in the past and the generated libraries were named "pc_ble_driver_shared_sd_api_vX.dll".
Now I compiled 4.1.1 and the libraries are named "nrf-ble-driver...
Dear Nordic:
My nRF82832 codes based on nRF5_SDK_15.2.0_9412b96 and used s132_nrf52_6.1.0. But I find the Bluetooth signal of nRF82832 can’t be scanned by smart phone which...
