Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hi,
I'm working on getting the DFU bootloader working and I'm following this blog post.
I'm successfully compiling and loading the bootloader to our custom hardware...
I want two pwm channel output 1MHZ frequency, the phase difference between two PWM channels is 180 degrees。when i set two pwm frequency to 500KHZ, use the configure below...
Hi,
We are testing an evaluation board nRF9160-DK with the firmware samples to build our own prototype. Is there a friendly process or example for FOTA to update the device...
Hey
I would like to know how can i connect 1 peripheral to multiple centrals(ex : 2 centrals), I am have three nRF52 DK boards for two centrals and one peripheral, My idea...
Hi,
Currently I am adding DFU support to our application, I was able to compile the secure bootloader example and use it.
my next question is, how do I enter DFU mode...
Using Rowley Crossstudio for ARM.
Using SDK V15.3.0 and S140 V6.1.1
When calling sd_softdevice_enable(..) it returns 0x1001 ( SVC handler missing ). Any suggestions ?
Hello Nordic Support,
Using the Nordic Power Profiler Kit v2.6.2, I can get the average current consumption for a maximum window of 120 s. Is there a way to get the average...
Hello Nordic Support,
Using the Nordic Power Profiler Kit v2.6.2, I can get the average current consumption for a maximum window of 120 s. Is there a way to get the average...
At present, I have a project that needs to add dual uart function, but 52832 does not have hardware dual uart function, so I need to simulate one serial port, I need your...
Hi all. I try to implement ble dfu bootloader project via getting start from SDK/examples/dfu/secure_bootloader/pca10056_ble_debug project.
Using:
OS: Linux
Compiler...
Hi!
This is a general question about iOS app distribution, but it regards our use of Bluetooth Mesh. I know it is each company's own responsibility to make sure they comply...
Hi there,
I am porting existing code from nRF52832 to nRF52840, and found that bootloader references to NRF_BPROT fail:
Apparently becuse the nrf52840.h in the mdk does...
Hi All,
I have loaded in the Bluetooth Mesh Light-Switch example and it works well.
For now, I would like to read out the received data from the switch node (client) to...
Hello! I am using SDK 15.3.0 to develop the NRF52832 firmware. At present, I want to implement a function, when the device is connected to the IOS host, start pairing, and...
