Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi, I try to adopt the twi_scanner example from the peripheral examples to the nRF52840 Dongle.
I followed the process in the following link with no success though.
https...
I'm trying to reduce the power consumption of my custom board with nrf52822.
With this code I get 93 uA:
If I enable only the app_timer I get 533 uA:
I'm using...
Hi
In a project with nRF52810 I use DMA of SPI and PWM to read data from flash and supply it directly to the pwm generator efficiently.
When reading from flash, I load...
Hi there,
I am porting the the app_button from the ble_blinky project to my own project which uses BLE functionality too, and it is not firing the button_event_handler after...
Hi,
I am developing one of the application using nrf51822 with SDK S110. in which I need to receive the long data(like image) through the mobile app.
And newbie to the...
I have problems using the Power Profiler Kit from nRFConnect v.2.6.1 with a nRF52832 DK on Ubuntu Linux 18.04 (KDE Neon). It is unreliable in opening the serial port, but...
Hello, We are developing a product that is based on the NRF52832. Currently in the certification phase, we are working with a Laboratory that is guiding us through the process...
Based on the nRF5_SDK_15.0.0_a53641a\examples\ble_peripheral\ble_app_uart\pca10040\s132 sample code, I've defined a long button(button 2) and 3 short buttons ( button 1, 3...
Hi everyone,
I've noticed in the changelogs of Version 2.0 in the nRF5 SDK for Thread/ Zigbee that the touclink support has been removed:
- Removed support for touchlink...
Hello,
I would like to set up in the same chip (nRF51) :
one open connection for an access control application – unlimited smartphones (no bond) and fast connection...
Following multiple articles on logging for enabling log output using Segger Embedded Studio and the Zigbee library I find they all seem to be missing something. Fundamentally...
Throughout the ZBoss API documentation there are references to source code snippets to help fill in the missing descriptions. An example is in the documentation for the Commissioning...
Hi Sir,
For 52840, we support the data rate 2M/1M/500K/125K.
If we want to test the modulation for 500K/125K (S2/S8), does the frequency deviation setting same as 1M...
hi folks ,
i want to reduce my power consumption so that battery life can be extend , my device function is it will read the data and send the data only if reaches the threshold...
