Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am attempting to port a custom ble service from sdk12 to sdk 14 and am a bit confused as to how to increase my uuid count. In sdk12 I did it like this:
uint32_t err_code;...
Hi
I am using wireshark 2.0.1(64 bit).When i am trying to capture the ble packets it showing error.I have attached the Wireshark error message.BLE Sniffer version 1.0.1.I...
In the Bluetooth Light Controller example for the client in main.c these constants are defined:
#define SERVER_COUNT (3)
#define CLIENT_COUNT (SERVER_COUNT + 1)
Why...
Hi Nordic,
Sorry if I missed and repeated a question, just point me to the previous answer if it has been posted before.
I am trying the DFU example found in the SDK...
Hello,
I'm wondering that it is ok to route ANT line through board-to-board connector to chip antenna.
Because there is no space to place nRF52832 and chip antenna together...
Hi,
I've seen that SDK 12.3.0 contains a new version of the application sample using the Eddystone protocol for BLE. I would like to know if this version is compatible...
I am using the template example for S130(works fine).
I tried adding a simple Pin interrupt on the code but it didn't call the pin interrupt handler everytime I press the...
For applications using the application UART Module ) via APP_UART_FIFO_INIT() without hardware flow control - how does an application put the UART peripheral to sleep?
...
Hello Nordic staff (or anyone in the know),
I saw this post from @newtom almost a year ago which concluded that I2S master library does not support 32bit words from mics...
Hello there,
I am a beginner, i want to know what changes should i make in the already existing example "ble_app_uart" so as to make my nrf51 development kit able to transfer...
In the file app_sdcard.c of the SDK13.0.0, an assert is done when calling app_sdc_init() with a pin P0.0. Can i safely use P0.0 with the assert deactivated or should i use...
Hi;
I am using nrf51822 qfaa device with sdk12.3. I compiled eddystone example code and it worked with nrf51dk(nrf51422_qfac) board. Also, i have a board that has nrf51822_qfaa...
I would like to use the POFCON register thresholds to create a crude battery level indicator. I noticed that the POFCON register definition in the nRF52832 Product Spec has...
Hello everyone,
I'm currently migrating from a functional code IAR to Eclipse GCC.
It compiles fine and I got the hex files.
However I have some troube to flash the...
