Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello,
When using eDRX alone and without DATA (eDRX=81,92 sec, no PSM, no data transmittion,iDRX PDCCH = 1), it's showing an average current of 17,84 uA. This value is similar...
Hi Support team,
I have downloaded nRF5 SDK and found that there is a sample for serial via UART but however the samples ( <SDK Folder>\examples\peripheral\uart) is available...
Hi,
I've designed a product based on nrf52840 soc as a central Bluetooth device. I want to pair and connect to a Bluetooth device (as a slave) that implements a whitelist...
Hello,
When AGPS is activated and trying to fix location, the user see only the final respond once fix is done, but we need to know where the satellites table is stored...
nRF21540
We want to use the nRF21540 FEM to improve BLE range and performance within a building. How does the Tx and Rx amplifier operation coordinate with the BLE SoftDevice...
Hi,
Related to this topic BLE DFU, MCU to MCU (Zephyr), GATT DFU SMP Service Clinet
I would like to know if anyone has any luck in making a SMP client for DFU updates...
I moved to a new computer and reinstalled all the tools and moved my code over. Now, when I compile, I get the following error:
Here is the code from the board definition...
I have an nRF9160DK that I'm trying to get a demo running per this video: https://www.youtube.com/watch?v=rMvW3HXLErk&t=832s
The board label says PCA10090, 0.8.5, 2019...
I had used ble_advertising_advdata_update function to update my scan response data in ibeacon by getting error as mentioned below:
.\_build\nrf52832_xxaa.axf: Error: L6218E...
I'm trying to get basic i2c code working on my Nordic nFR9160DK board. I'm new to the platform and have been doing a lot of reading and searching through examples. Through...
Hi
In order to work on never zephyr version I have tried updating my ncs v1.7.1 folder to origin/main with:
git fetch origin git checkout origin/main west update
After...
Hi,
Does the ratio of gain error and offset error change when the ADC gain is changed?
For example, if the gain is 1 and the gain error is 4% and the offset error is...
Hello!
I am wondering what the At command %XDATAPRFL does? It says that it sets the application data profile but i couldnt find any info about what this really means....
Hello there,
I'm working on a "handsfree" audio guide for a museum application. Right now I'm exploring BLE to trigger the audio files based on the received signal strength...
Hi
My problem with SES are:
Variables are almost impossible to watch or view in memory, It's a lottery basically.
The other thing that bothers me is no code folding...
