Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello,
We are trying to use `nrf_modem_lib_shutdown` to turn off the modem before entering system OFF mode. We are using LTE link control, with the following LTE settings...
I am using the nrf52832 with softdevice s112
is the app_timer library still limited to the max period of RTC1 as explained in this post https://devzone.nordicsemi.com/f...
I seem to have this issue on this page in the info center https://infocenter.nordicsemi.com/topic/sdk_nrf5_v17.0.0/group__nrfx__saadc__v2.html
when I click on "API description...
Hi, Dear Nordic & all:
I just want load and run the “serial_lte_modem” example about NCS 1.5.0's project in SEGGER(no file modified) on nRF9160 DK，but there is something...
Hi!
I just wanted to try out the online power profiler. It seems like it is currently not available.
Is this the correct link still https://devzone.nordicsemi.com/nordic...
Hi
testing with thingy91 v1.4.0, firmware 1.5.1.
I never succeeded to enable passive mode of nrf_asset_tracker_v2 no acceleration is detected.
Someone experience the...
Hi,
I'm new to use nrf52832, just as I said above, I want to know if the version of softdevice support bluetooth 5?
Where can I know these information?
Hello,
I've recently been porting a program over to Zephyr and hoping someone here might be able to shed some insight on this issue.
I can't seem to get flash_write to...
Hello,
I want to test a peripheral that uses private address resolution. I would like to set nrf52 eval board used by the nrf Connect Desktop to use a fixed, private random...
Dear Nordic engineers
I recently encountered a problem while developing the program of nRF52833.My program is developed on the basis of nRF5SDK 16.0, using S140 softdevice...
Hi, We recently made a custom board for a new project, based on the nRF52832-QFAA. Everything looked fine in the first place as the nRF is perfectly recognized on a PC and...
On the Eval board layout, the 2 nd and 3 rd layer cut away under the RF trace. That make the substract height equal to 57.87 mil.
For 30 mil width trace, the impedance will...
Dear Nordic support,
i'm evaluating the Nordic nRF52840_Dongle with the SDK 1.5.1, inlucing Zephyr etc. I could successfully compile and load the Blinky-example (..\ncs...
Online orkunsengur 2 days ago
Hi,
When I create and open an project, and I can go project options-->preprocessor-->include directories etc. However, if I use example...
