Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am trying to port existing software to a custom nrf9160 board. I am using latest nrf connect sdk updated with git and west. Could somebody from Nordic comment about the...
I tried to increase the bootloader size by reducing IROM start address and increasing size but I always get the same error:
.\_build\nrf52832_xxaa_s132.axf: Error: L6407E...
I would like to perform FDS garbage collection only when it is close to being full. I can read the fds_stat to see the number of words used and the words freeable but what...
Hi all,
I would like to get the complete name from the connected peripheral by reading the device name characteristic (0x2A00) in the Generic Access Service (0x1800). I...
I want to use sys_time_get() on my ble app in SES env. but it looks like sdk 14.2.0 doesn't support sys_time_get() on SES env. So I'd like to use the similar function such...
Hi
Am new to the nrf52382 , Am trying to establish connection between nrf52382 DK as peripheral and nrf connect app as central,
Am unable to connect it .Please debug...
Hi, I am using nRF52832 with sensor, nfc , Softdevice S132 v6.1.0 and SDK 15.2.0 to advertising packets .The sensor is interfaced with nrf52832 using twi interface. I have...
I learned from the following support ticket link that for adding a pre-bonded LTK to the nRF52 bonding store, I can call pm_peer_new().
https://devzone.nordicsemi.com/f...
Hi,
I am trying out the udp_with_psm example from: https://github.com/Rallare/fw-nrfconnect-nrf/tree/nrf9160_samples/samples/nrf9160/udp_with_psm as a first step in sending...
Hi Team,
I planned to have product with this nRF52832 chip and now development was getting stopped because of known issues on SAADC on this nRF52832 chip. When I am seeing...
Hi. I am developing application that should work both ANT+ and Bluetooth. For bluetooth connection I am testing with nrf connect for pc, but I was wondering if there is similiar...
Ran in to a build error when using nrf_fstorage_nvmc.c: \components\libraries\fstorage\nrf_fstorage_nvmc.c(128,19): error : conflicting types for 'write'
nrf_fstorage_nvmc...
Hi,
I'm working with the latest software version of nrf52840.
Can you kindly specify the exact addresses of:
1. Flash usage of Softdevice
2. RAM usage of Softdevice...
Hi Team,
We are currently validating a BLE enabled embedded device. The device has an ARM Cortex M0 chipset and uses Dialog Semiconductor for BLE.
Could you please let...
When using the 0.7.0-15.alpha firmware release. What is the best application side code to go with it. Should still tag v0.3 be used of: zephyr, nrfconnect and nrfxlib?
...
