Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hi,
I'm trying to setup the Peer Manager on a nRF51822 with installed the S130. I'm working with Eclipse where I installed the 12.3.0 SDK.
At compilation time I get the...
Hi, I have a two part question, I know the NRF51822 (and I believe all 4.0 BLE chipsets) are being sunset, when will this start taking place?
Since I'm currently using the...
HI,
i am using nrf51422 with sdk13.3.0 and soft device 130
i am receiving 69 byte of data through UART, i am compressing data in two packets. here after transmitting a...
I have an issue with BLE on Android when using low duty-cycle directed advertising and I'm asking here hoping some people have already seen that issue or something similar...
Hi,
I'm working on a custom bootloader based on the one included with SDK 15.
I have a blocking method (i.e. while loop) that runs at the end of the transmission of all...
Hi,
Some general Nordic BLE device questions:
How to add Characteristic?
How to send data to given c haracteristic?
We are using SoftDevice 132 with Segger IDE.
...
I am trying to free up some RAM on my nRF because I am getting Fatal error 0x4, NRF_ERROR_NO_MEM when I try to increase the size of a 2D array.
I do not understand how to...
Hi there,
I am considering the NRF52840 to build our new platform but I am struggling to find information about how the device Firmware is programmed.
Apart from SWD...
Hi,
I'm using sdk 15.2, with soft device s140 on nrf52840 dongle in peripheral mode. I'm using modiffied ble_app_proximity example. What I wan't to achieve is to set advertising...
I want SoftDevice of Bluetooth 4.2 for nrf52832.
I found softdevice.
15.2.0 nRF5 SDK
15.1.0 nRF5 SDK
15.0.0 nRF5 SDK
14.2.0 nRF5 SDK
etc
Which is Bluetooth 4...
i have one huge process one get positon sensor using i2c bus and another get led color also using i2c bus.
when color function is added in the process,positon sensor data...
Dear all,
I defined "DEBUG" , used UART peripheral and "printf()" in the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96. I find nRF52832 always dead in the place at...
Hello,
To determine the current network topology I hoped I could use the heartbeats to determine the RSSI and the number of hops. The RSSI of the last node is in the example...
