Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I'm using three nrf52840-dk's, from an ubuntu 16.04 x64 host.
JLink v6.30b
nrfjprog v9.7.2
I can program and interact with two boards fine, with zero of the failures...
hello all ,
controller nrf51822
i am trying to development for EPD 7.5 spi interfacing through external flash image send .
my question is i am using reference code for...
Hi, everyone,
We are developing BLE project on nRF52832 chip by using SDK14.0 software.
The project is build from one master-device and many slave- devices.
The master...
hi............
i want to modify the ble hts program , inorder to add a timer in it. i want to transfer the data for every one minute ,so data have to read for every one...
Hi.....
i want to transfer the data for every one minute from peripheral device to phone (nrf connect ).. how to declare in the program and what function to be used ?
...
hello,
I use buttons_leds_init(&erase_bonds) to get data from AS3933 LF chip after it give nrf52810 a wake signal. But after i start a app_timer, the button bsp_event_handler...
Hello Everyone,
i am trying to create the new project in keil version but i dont know how to include library files and how to create new program file please help me in...
Hello, is it possible to receive and transmit RSCS characteristic on only one nRF51 DK ? If merging rscs_example and rscs_c_example into 1 project is a good idea ?
Hi,
I'm having issues getting code to run using nRF51 SDK 10.0, on an nRF51822xxac.
I am using the pca10028 ble_app_hrs_c example, and the inculded softdevice "s130_nrf51_1...
Dear all
I am currently working with a nRF52840 Dongle, the ble_app_blinky_s140 example.
To power some external circuits i have to set VDD to 1.8V.
Until now i tried...
hi, this is Shivaji, I have to work on Bluetooth mesh, so which kit I have to buy, can I buy thingy52 or can I buy nrf52dk. which board should I buy, and can get the android...
Dear Sir,
I have bought a BMD 300 chip.
I have implemented a firmware with segger embedded studio and SDK15 for nrf52832.
I have flashed it to BMD300 DK from Rigado...
Hi:
As we are going to use nRF52840 on our product, we were trying the check the HW security implemented in the chip. nRf52840 implemented Arm TrustZone CryptoCell-310 in...
Hi Team,
I hope you are doing good.....
I am using nRF51822 with the SDK version 12.3.0 in windows, keil version is 5.26.
In the blu_app_uart Application i want...
Hi,
In order to isolate the issue, I've created an app that :
1. switches to dc2dc mode.
2. calls sd_app_evt_wait()
I still see 3ma consumption,
any ideas...
