I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I have a strange problem running the CLI example in the DK on the Nordic dev board with SES: It works fine with build/run, but when trying to debug it pops up a message that...
I am using the nRF52832 in several projects for several different clients. I have created a "project" under Visual Studio using VisualGDB for each one, using the automated...
Hi,
I would like to know how to raplace a MPU-9250 chip with ICM-20948 in a Thingy:52 circuit.
Let me first state that my electronics engineering knowledge is at hobby...
So I've had a LOT of problems getting power management to work with UARTE on the 52840. We're using both UART_0 and UART_1 and have finally gotten UART_0 to work as it should...
When attempting a DFU update (containing APP + SD + BL) with the android version of nRF Connect, it appears that connect will update the device's application even when bootloader...
Is it possible to pass a memory location to PWM (preferably via DMA) via PPI. This is a sound project and my intent is to update two 8 bit PWM outputs at 44.1kHz. I typically...
Hi,
I am working on a project and I want to program the nrf52832 with the arduino IDE with this package ( https://github.com/sandeepmistry/arduino-nRF5 ). I want to use...
Are there any restrictions (eg, timing) or issues for using different references for different channels in Scan mode?
eg
AIN0 uses VDD/4 as reference;
AIN1 uses VDD...
Hi All.
Do someone know what is the oversize I get when I use the FS_storge example to store data on the interanl FLASH.
FOr every bulk I open (id+key). How much bytes...
I'm using nrf51822 and SDK 10, S110 Softdevice. Implemented whitelist using device manager and bonded with single device , after bonded my device with phone (using nrfconnect...
I'm using nRF51822 and SDK 10 , Softdevice S110 . I enabled whitelist option in my application its working as expected, but when after device is resetting peer device data...
Hello,
I am working on an application on a nrf52840 using soft-device 140 and SDK 15.3. I have written 90% of the application using the ble_app_uart_c as a template for...
Some context: I am using an nRF51 with SoftDevice S130, which acts takes both central and peripheral roles, and uses UART to communicate to a peer MCU. I am currently facing...
Hello,
I am using Seeger for Flashing code and Debugging. I ported code from “flash_fstorage” example code to “ble_app_blinky”. I have few queries on write data into Flash...
Hello,
I am trying to configure Pin P0.09 as SCL pin for TWI. But I am not getting any results with this pin while I get data when any other GPIO pins are configured as...
